UXSPI hangs when attempting to perform updates on IBM System x3950 X5 type 7146 The IBM System x3950 X5 could hang after selecting Updates from the TUI or GUI menus, and Share?Profiles ▼Communities ▼Apps ▼ Forums IBM BladeCenter Forum Log in to participate Expanded section▼Topic Tags ? UXSPI fails to stop at a prompt to update VMware EXSi When you use putty to log into Linux OS and then run a UXSPI command line on a remote Linux Log in to reply. http://domcached.com/ibm-error/ibm-error-flashing-firmware-15.html
To have UXSPI continue, double click Close the Program. I got this particular during the upgrade of the DSA. UXSPI fails to detect the Broadcom firmware version UXSPI fails to detect the installed version of the Broadcom NIC on IBM® System x®3100 M5 for Windows and Linux. UEFI, DSA, and IMM updates all failed with the same error code 41. https://www.ibm.com/developerworks/forums/thread.jspa?messageID=14614006
Error Starting Firmware Upgrade (0006) The Specified Image Is Not Found
The "Current Interrupt Assigned" field on the "PCI Interrupt Routing" menu displayed incorrect values. One or more updates did not install during deployment. If you are using UXSPI 4.40, install Brocade driver 220.127.116.11.
The file is available for download from the IBM Support Fix Central web page.
Watson Product Search Search None of the above, continue with my search Update Manager: Flashing IMM/DSA/UEFI on Some Linux Servers Fails IBM Systems Director Usage General - All Platforms 18.104.22.168 22.214.171.124
Limitations: Dependencies: Version 1.02 - BuildID: BAE123AUS Problem(s) Fixed: Corrected a spelling mistake within the Flash Utility.
Firmware ibm_fw_hdd_sas-1.10.01_linux_32-64 displays different versions The SAS/SATA Hard Disk Drive (HDD) Update Program incorrectly reports different versions of both the installed version and the update version of the firmware.
Previously these IDs would after a reboot which can cause Windows Server 2008 to detect previously installed devices as new devices and reinstall them.
Log in to reply.
UXSPI cannot restore the multi-node interface IP after an update If you set the static IPs for IMM usb0/usb1 on a multi-node system, UXSPI might configure these IPs to workable ones,
The update will complete normally.
This is the accepted answer. Configure the firewall to allow uEFI/DSA/IMM updates on uEFI/IMM systems To perform these updates, you must configure the firewall to ensure that the flash utilities can connect to the IMM. BMC code fixed their IRQ table handling which caused an extra time for AP init. UXSPI runs slowly on Windows multi-node systems When initially running UXSPI on a multi-node system that is running Windows 2011, it can take up to 15 minutes for UXSPI to start.
Ensure the Telnet connection is enabled and the password has not been changed for Cisco switches Click Reset the switch to factory defaults on the management page for the Cisco Switch Ibm Updatexpress System Pack Installer User's Guide After the updating competes with success, abort the command executing. x460/MXE-460/x3950 is only supported in single node Multi-node support is not available for x460/MXE-460/x3950. https://www.ibm.com/developerworks/forums/thread.jspa?messageID=14838833 Previously, when a memory mismatch was detected the chassis fault LED and the blade's fault LED were not turned on.
Abnormal GUI when saving logs in a bootable environment When saving log files in a bootable environment, the layout of the buttons in the GUI might not be consistent. Note: You now have two ways of downloading files with the *.sh extension. Intel, Red Hat, SUSE, and IBM are still investigating this issue. The probability of occurrence in the field is low, but IBM strongly recommends updating to this code as quickly as possible to prevent any data issues from occurring.
Ibm Updatexpress System Pack Installer User's Guide
You must open HTTP port 80 and HTTPS port 443 in order to use the acquisition function. Added I/O Memory Map Unit (IOMMU) menu option. This lead to a 3 boot failure, and default settings being loaded. To avoid this problem when updating IMM firmware from a USB key, perform the firmware update as a separate update, or perform any other updates prior to updating the IMM firmware.
Duplicate IP addresses when updating IMM, uEFI, and DSA When using UXSPI to update IMM, uEFI, and DSA, you might encounter IP address duplication. Mikky83 270001YC71 2011-05-06T14:29:37Z Hello, Did you find solution for this? Corrected PXE boot failure observed on the secondary NIC. check over here If the update is detected, this field shows the individual update contained within the update package.
You can use this UXSP to update on Windows 2008. RandyC 2700004U26 1 Post Re: DSA 3.33 Firmware update 2012-02-15T23:36:51Z This is the accepted answer. Only the BIOS versions of the QLogic FC firmware are detected.
This driver is always installed.
However, you can disable it. The installation of a Mellanox firmware update, however, is not dependent on the MFT. same happened to me. Hi evryone!
this worked for me. If the IPMI drivers are not running, the IMM firmware version cannot be detected. Linux device driver updates require specific packages The Linux device driver update packs require the following packages to be installed:Red Hat Enterprise Linux: rpm-build, perl, and bash SuSE Enterprise Linux: perl Unable to validate userid/password on IMM at IP address 169.254.95.118.
The following error is displayed when the product tries to update the second OS image: Could not find update file. You can ignore the testing proxy connection and continue acquiring packages. Added workaround for Opteron errata 150. Updated URL information within the readme.txt.
Acquisition of Windows updates does not distinguish between the different versions of Windows Windows 2000, Windows 2003, and Windows 2008 updates are organized in a single Windows UXSP. The status now shows red and reports "Invalid CPU Configuration" if a CPU mismatch is detected. Regards Log in to reply. Comparing the update BIOS version to the installed BIOS version is sufficient to determine whether the QLogic firmware is a previous version.
For other peoples future reference we had the same issue when tyring to update the uEFI and IMM on a 3550 M3, would just error out with error 41, logged a To interrupt the local process, log on to the remote system and manually stop the UXSPI process.