Home > Hp Scanjet > Hp Scanjet G3010 Error

Hp Scanjet G3010 Error

Reconnect the power supply and turn on the scanner. Do you wish to proceed to the home page of the new product? If the base unit self test results were as described above, then the test was successful. Sorry for the confusion. -------------How do I give Kudos? | How do I mark a post as Solved? -------------------------------------------------------- Reply 0 0 « Message Listing « Previous Topic Next Topic » have a peek here

Privacy Policy Ad Choice Terms of Use Mobile User Agreement cnet Reviews All Reviews Audio Cameras Laptops Phones Roadshow Smart Home Tablets TVs News All News Apple Crave Internet Microsoft Mobile Please try again later. I know the sacnner and the iMac are talking as on start up the scanner makes its "start up noises'. Simultaneously press and hold the Edit Text and E-Mail buttons (Approximately 2 Seconds). http://h20564.www2.hp.com/portal/site/hpsc/public/psi/troubleshootResults?sp4ts.oid=1849437

The carriage will continuously move the full length of the scanning bed. Connect with us facebook twitter CNET Reviews Top Categories CNET 100 Appliances Audio Cameras Cars Desktops Drones Headphones Laptops Networking Phones Printers Smart Home Software Tablets TVs Virtual Reality Wearable Tech To end the test, disconnect the power cable from the back of the scanner. If you receive a message '...Driver comes from an unidentified developer', follow these steps: Click OK to ignore and close the message.

  • If, after installing HP Solution Center successfully, another HP device is not working properly, the exported directory key data can be added back to the HKEY_LOCAL_MACHINE\SOFTWARE\Hewlett-Packard directory by double-clicking on the
  • Turn unit off.
  • Initially success in that this time I got a window looking for the hardware (scanner).

The product could not be added to your profile at this time. Select the scanner model and click Uninstall. Please wait while we process your request. Please try again now or at a later time.

Press and hold the Copy and E-mail buttons on the front panel, and connect the power cable to the scanner. Leave the power module connected to the power source. HP Customer Support Support Home Products Software and Drivers Forums Contact Support Search Select your Model Let HP find my products Identify now HP can identify most HP products and recommend When you hear the self test start, release both of the buttons.

I am fairly convinced at this point that there is a hardware issue.Thanks a bunch though for the tips about Preview and Image Capture!Thomas Flag Permalink This was helpful (0) Collapse Proffitt Forum moderator / January 21, 2015 2:32 AM PST In reply to: Scanjet HP G3010 "HP Scanjet Full Feature Software and Drivers for Mac OS X v10.6"After I answered the Leave the power module connected to the power source. Disconnect the USB Interface cable and the ADF Accessory cable from the back of the scanner.

During a successful base unit self test, the scanner will do the following: The scanning lamp will light up. you can try this out The ability to move the carriage. Z7_M0I02JG0KONJ30ACBBF8MM1084 hp-hero-support-search Actions ${title} Loading... The three in one is attached via a Cat 5 cable; the flat bed is attached via an USB cable.The problem with the flatbed manifested itself well before the three in

top Step three: Remove the Hewlett-Packard directory or key from the registry Clean up the registry. http://domcached.com/hp-scanjet/hp-scanjet-4370-error.html All submitted content is subject to our Terms of Use. Scanner runs fine on other Lenovo desktop models with the same configuration.Used diagnostic tool of website: some drivers are missingWhat else can we do. NOTE: As a best practice, HP recommends that this setting be set to ‘Mac App Store and identified developers.

To end the self test, set the power switch to the Off position. top top Troubleshooting error messages received during installation When you try to install older software released prior to Mountain Lion, you might receive the following error message: '...Driver comes from an NOTE: Please DO NOT install older software from any HP CD that might have come with the HP Scanjet. http://domcached.com/hp-scanjet/hp-scanjet-5590-error-8-1-0-1.html The carriage will continuously move the full length of the scanning bed.

If the base unit self test results were as described above, then the test was successful. The LCD will display Diagnostic Mode. The default diagnostic speed can be changed by pressing the (select destinations) toggle button.

Software?

To do this, follow these steps: Open System Preferences and then under the Personal section, click Security & Privacy. To end the test, disconnect the power cable from the back of the scanner. That makes me think you didn't install the rest of the package.Bob Flag Permalink This was helpful (0) Collapse - Once again into the fray by Thomas969 / January 24, 2015 Flag Permalink This was helpful (0) Collapse - I read that too, but then I tried "Mac OS X" by R.

During a successful base unit self test, the scanner will do the following: The scanning lamp will stay lit. After the carriage moves the full length of the scanning bed a couple of times, the scanning lamp will blink several times. Check. this contact form IBM WebSphere Portal Home IBM Logo Sign Up Log In Welcome Getting Started Contact HP - Anonymous Contact HP Product Context View Support Home Test page Product Home Product Warranty Result

If you cannot find your product on this site, go to HP Support Center - Hewlett Packard Enterprise. Please try again later. The good news,The bad news is when I went to do a scan I again got the error message no device found.Ain't technology wonderful !!Once again, thank yous to all! note: There is no carriage self test for this scanner.

If the base unit self test results were as described above, then the test was successful. HP Scanjet 8300 To enter diagnostics mode: Disconnect the power supply from the back of the scanner base. When a second install is attempted, either over the previously installed software or after uninstalling the previously installed software, the install appears to complete in that all install steps are started note: The TMA cable must be connected to perform a self test on the HP Scanjet 4800 series because the buttons to start the test are located on the TMA (document

The following should occur: The scanning lamp will light up. To reset the scanner for testing other buttons, press the desired button.