Home > Hp Scanjet > Hp Scanjet 3770 Lamp Error

Hp Scanjet 3770 Lamp Error

Press and release the Scan Document button. With the power module connected to the power source, connect the power module cable to the back of the scanner If the power switch located on the back of the scanner Hev Level 3 Expert 1059 Answers Tony Isted Level 1 Expert 49 Answers gbob59 Level 3 Expert 2963 Answers Are you a HP Scanner Expert? Next, make sure ... http://domcached.com/hp-scanjet/hp-scanjet-3770-error.html

Reconnect the power supply and turn on the scanner. HP Scanjet 2300 and 3670 Disconnect the Universal Serial Bus (USB) and power cables from the back of the scanner. Sell on Amazon Image Unavailable Image not available forColour: 12V HP Scanjet 3770 Scanner replacement power supply adaptor by MyVolts Be the first to review this item Price: £7.49 In stock. Clean the adapter windows using a slightly damp, soft cloth.

top Scanner installation or setup issues This section contains solutions for installation and setup problems. Browse Categories Answer Questions HP Scanjet 3770 Flatbed Scanner HP ScanJet Scanner HP Scanner Scanners All Unanswered Join Sign In Ask a Question × HomeForumScannersHPScanJetHP Scanjet 3770 Flatbed ScannerLamp error scan Leave the power module connected to the power source. Press the Scan Slides or Negatives button and look for illumination in the TMA.

If the base unit self test results were as described above, then the test was successful. Is this just a bulb replalcement? To end the test, disconnect the power cable from the back of the scanner. Working...

Question about HP ScanJet Scanners 1 Answer Hi I need the service ...error, in fact the lamp is on, until scan begin, and, immediately get off, so the result is a The HP Image Zone software might need to be reinstalled. Close the document cover. http://support.hp.com/us-en/document/c00030441 I followed I'm getting a lamp error on my 2400.

Verify that the transparent materials adapter (TMA) cable on the scanner lid is connected to the center connector on the back of the scanner. Question about HP ScanJet Scanners 1 Answer HP Scanjet 4400c ...Error ActiveX component can't create object "chasis. When you hear the self test start, release both of the buttons. During a successful base unit self test, the scanner will do the following: The scanning lamp will light up.

  1. top Problems scanning slides or negatives The image cannot be enlarged Zoom in was probably selected instead of Resize.
  2. Please wait while we process your request.
  3. A software conflict might exist on the computer.
  4. I've tried with Windows scan, HP ...
  5. The scanning lamp will light up and stay lit.
  6. Press and hold the Copy and Scanning buttons on the front panel, and connect the power cable to the scanner.
  7. Turn unit off.
  8. If not, then it is most likely bad.
  9. The product could not be added to your profile at this time.
  10. The scanner lamp should flash six times while the carriage is still in motion.

Reconnect the power supply and turn on the scanner. The LCD will display Diagnostic Mode. irisecommerce 1,555 views 5:58 magazineluiza.com Scanner HP G4050 - Duration: 1:26. The LED on the front panel will light up orange.

During a successful base unit self test, the scanner will do the following: The scanning lamp will light up. navigate here If your bulb is coming on, but you still receive the ... Loading...Oops :Please try again. HP Scanjet 8300 To enter diagnostics mode: Disconnect the power supply from the back of the scanner base.

Modify your browser's settings to allow Javascript to execute. To end the test, disconnect the power cable from the back of the scanner. With the lid open, simultaneously press the Scan Film and Copy buttons (second and third from front of scanner) while turning on the scanner with the power switch at the back. http://domcached.com/hp-scanjet/hp-scanjet-4070-lamp-error.html The carriage will continuously move the full length of the scanning bed.

After a few seconds, the carriage will continuously move the full length of the scanning bed. If the base unit self test results were as described above, then the test was successful. To end the test, disconnect the power cable from the back of the scanner.

HP Customer Support Z7_3054ICK0KGTE30AQO5O3KA30U7 hp-contact-secondary-navigation-portlet Actions ${title} Loading...

Disconnect the USB and power cables from the back of the scanner. Question about HP ScanJet Scanners 1 Answer When i try to scan i get a lamp error nessage when i try to scan i get a lamp error nessage Has it Question about HP ScanJet Scanners 1 Answer Hp scanjet 3970 on Mac: lamp error ...lamp error Normally this error means that your lamp will no longer come on to scan anything. Country: United States Select a location Americas Europe, Middle East, Africa Asia Pacific and Oceania Select a language Confirm Back Z7_M0I02JG0KOT530A6KJKFRQ0816 hp-detect-load-my-device-portlet Actions ${title} Loading...

If the base unit self test results were as described above, then the test was successful. Sign in to make your opinion count. During a successful base unit self test, the scanner will do the following: The scanning lamp will light up. this contact form Answer questions, earn points and help others Answer questions Manuals & User Guides Have a manual for HP Scanjet 3770 Flatbed Scanner?

Sign in Share More Report Need to report the video? Press and hold the Copy and E-mail buttons, and connect the power cable to the scanner. See your browser's documentation for specific instructions. {} Z7_3054ICK0KGTE30AQO5O3KA30U5 hp-support-head-portlet Actions ${title} Loading... Leave the power cable plugged into the wall power outlet.

HP Scanjet 5470 and 5490 Disconnect the USB, XPA, ADF, and power cables from the back of the scanner. If the scanner completes the sequence correctly, the scanner is working correctly. The default diagnostic speed can be changed by pressing the (select destinations) toggle button. Question about HP ScanJet Scanners 3 Answers MY SCANNER GIVES ME A ERROR MESSAGE THAT SAYS LAMP ERROR Sorry, no spare parts are available.

Press and hold buttons 2 and 4 simultaneously for two seconds.