Home > Hp Psc > Hp Psc 1300 Series Error

Hp Psc 1300 Series Error

Contents

Bought NEW Office Max brand cartridges (both black & color). I have just installed 56 black cartridge, do you think 57 color cartridge is necessary for the printer to copy or print the document? Figure : HP PSC 1200, 1310, 1340, and 1350 control panel with the lights indicated On/Resume light Check Paper light Check Print Cartridge light Copies display (where an 'E' might display) Step three: Replace the USB cable Securely connect an alternate USB cable to the rear of the product. http://domcached.com/hp-psc/hp-psc-1300-series-print-cartridge-error.html

If any torn pieces of paper remain inside the product, more jams are likely to occur. Language: English (UK) Content location: United Kingdom Restricted Mode: Off History Help Loading... HP Printer Support 61,401 views 8:41 my HP Deskjet F380 All-In-One Printer - Duration: 2:46. You can change this preference below. http://h30434.www3.hp.com/t5/Inkjet-Printing/my-psc-1300-displays-an-quot-E-quot-error-despite-new/td-p/716731

Hp 1350 Printer Check Print Cartridge Error

If the issue persists, continue to the next solution. How does HP install software and gather data? If these steps resolved the issue, you do not need to continue troubleshooting. Solution four: Service the All-in-One If you have completed all the steps and are still experiencing a problem, continue to the Service the All-in-One section at the end of this document.

  • by bnf on Dec 19, 2005 at 12:31pm Add comment Please sign in to comment Did you ever get the encoder strip fixed?
  • Follow these steps to perform a partial reset of the product.
  • When only the On/Resume light is flashing, release both buttons.
  • I was very frustrated and was ready to junk the printer when I came across your suggestion.
  • h10025.www1.hp.com Also, make sure your computer meets the minimum system reguirements for the printer.
  • Paper jam causes The following factors can cause paper jams: Paper loaded incorrectly in the paper tray.
  • The sequence must be completed within ten seconds.
  • You can only upload videos smaller than 600MB.
  • I think part of the problem is, that it had jammed before it broke down and I pulled the stuck paper through the front and not the back.
  • In the program being printed from, click File, click Print, click Properties, and then click the Paper/Quality tab.

The first sheet might just barely move but thats all, also it seems that the sound of the paper pick up has changed, and not in a good way. by moe on Jan 19, 2011 at 2:02pm Add comment Please sign in to comment 0 Thanks, I posted the first question on 12/17/10 and stated that I did all the About Press Copyright Creators Advertise Developers +YouTube Terms Privacy Policy & Safety Send feedback Try something new! The carriage moves to the center of the product.

The printer should print a test page.5. Press and release the Cancel button () again. The 'E' symbol is showing in the number of copies box. click resources Solution nine: Service the All-in-One If you have completed all the steps and are still experiencing a problem, continue to the Service the All-in-One section at the end of this document.

Happy St. Loading... Solutions Solution one: Turn the All-in-One off and then on again Follow these steps to turn the product off and then on again. Solution five: Check for carriage obstructions Follow these steps to make sure that the carriage can move freely.

Hp Psc 1350 Printer

All the lights flashed and would not respond to any thing I could do. Why is my printer making a high pitched noise? Hp 1350 Printer Check Print Cartridge Error h10025.www1.hp.com Do a Reset Disconnect and then reconnect the power cord. Remove and clean each cartridge one at a time.

Ink Cartridge Problems - sometime ink cartridge is not being detected by the printer. this contact form Issue: The Check Paper light blinks In this error condition, the following blinking lights pattern displays on the control panel: On/Resume light: On Check Paper light: Blinking Check Print Cartridge light: Solution three: Install the HP software You must download and then install the HP product software in order for your computer to detect the product. If the product does not turn on automatically, press the On/Resume button () to turn the product back on.

When the lights begin to blink, press and hold both the On/Resume button () and the Paper Size button at the same time. Reply 0 Reply 0 0 Kryten Master's Graduate Posts: 431 Member Since: ‎04-07-2010 Message 2 of 2 (2,588 Views) Report Inappropriate Content Re: my psc 1300 displays an "E" error despite Please try again later. have a peek here Add to Want to watch this again later?

hp56 black by vasilako on May 2, 2011 at 10:20am Add comment Please sign in to comment 0 I have read through all the questions and find that a number of After the computer recognizes it and does it's thing, hit the Power and Cancel button on the printer at the same time. Try the intended task again.

Trending How can I print, or send to the printer yahoo email? 4 answers Who can i download bluetooth for wnidows7? 4 answers After fitting a compatible colour cartridge in a

Press the On/Resume button () to turn off the product. The reset is now complete. Is there a paper thickness adjustment somewhere? I hope someone can help me I really don't want to buy a new printer (but I need one know) by unknown on Jun 1, 2009 at 3:50pm Add comment Please

Press and hold the Cancel button (), and then press the Start Copy Color button. Follow these steps to plug your product directly into a wall outlet. Step one: Make sure that the carriage can move freely Press the On/Resume button () to turn on the product. Check This Out Loading...

Disconnect the power cord from the rear of the product. Load plain, white paper into the paper tray. Solutions Solution one: Wait for the All-in-One to complete the job Allow the product to complete the job. Doing so can cause bad electrical connections, clogged ink nozzles, or poor print quality.

Z7_3054ICK0KGTE30AQO5O3KA30N0 hp-concentra-wrapper-portlet Actions ${title} Loading... In your case it's probably just a bad cartridge. any clues as to what i need to do?!?!? The product prints a self-test report.

The alignment page prints.