Home > Hp Officejet > Hp Officejet H470 Error Lights

Hp Officejet H470 Error Lights

Contents

Press and slide the notch with a screwdriver, and then rotate the ink service module to the left to remove it. Close the cover on the product. Cartridges marked with a square or pentagon go into the right carriage slot. CAUTION: Only remove or install cartridges when the carriage stops moving. http://domcached.com/hp-officejet/hp-h470-error-lights.html

Figure : Close the cartridge cover Close the cover on the product. I had tried your suggestion already. Open the cover on the product, and then wait until the carriage is idle and silent. My frustration is with HP as they have been little or no help to me. http://support.hp.com/us-en/document/c01182351

Hp Officejet H470 Reset

Release the Power button (). Solution two: Print in Reserve Mode You can remove the black cartridge and continue printing with only the tri-color cartridge. Solution three: Service the printer If you have completed all the steps listed above and are still experiencing a problem, continue to the Service the printer section at the end of The following light pattern displays on the product control panel: Resume light: Blinking Left Cartridge light: Off Right Cartridge light: Off Power light: On Figure 12: The Power light is on

  1. Good luck ℜ a i n b o w 7000I work on behalf of HP★Click the “Kudos Thumbs Up" at the bottom of this post to say “Thanks” for helping!
  2. Blinking lights can indicate error conditions.
  3. NOTE: Printing in Reserve Mode might affect the color results and the print speed.
  4. Release the Power button ().

In the meantime, I took the full module out, completely washed it out (very messy) and put it back. Figure 28: Remove the black cartridge from the carriage slot If there is tape on the cartridge, remove it. Remove any loose paper or obstructions found. Hp Officejet H470 Resume And Power Light Blinking The Right Cartridge light and the Resume light turn off and the product is ready to print.

If the carriage is stuck in the middle of the product, move the carriage to the right side of the product. warning: You must disconnect the power cord to move the carriage by hand and reset the paper feed mechanism without risk of electrical shock. If pieces of paper remain in the product, more paper jams can occur. http://h30434.www3.hp.com/t5/HP-Connected-Mobile-Printing-and-Cloud-Printing/HP-Officejet-H470-Blinking-Lights/td-p/2755255 CAUTION: Do not touch the ink nozzles.

note: Clean the contacts quickly so that the cartridge is not outside of the product for more than 30 minutes. Hp Officejet H470 Cartridge Stalled Clean cotton swabs or any soft, lint-free material that will not stick to the cartridges (coffee filters work well). Solution two: Clean the cartridge contacts Follow these steps to clean the cartridge contacts. Videos English Open Menu English Deutsch Español Français Português 中文 한국어 † The opinions expressed above are the personal opinions of the authors, not of HP.

Hp Officejet H470 Ink Service Module Reset

When the printer is turned on, it goes through the normal start-up cycle, but then gives an error light pattern ofresume light and right cartridge light blinking, power light off. Disconnect the power cord from the back of the product. Hp Officejet H470 Reset Solution two: Clean the problem cartridge contacts Follow these steps to clean the cartridge contacts. Hp Deskjet 460 Flashing Lights If these steps resolved the issue, you do not need to continue troubleshooting.

If the issue persists, continue to the next solution. http://domcached.com/hp-officejet/hp-deskjet-460-error-lights.html Figure 29: Remove the tape Reinsert the black cartridge into the empty carriage slot at the same angle you removed it. When the cartridge initialization completes, the carriage returns to the home position on the left side the product. Press and hold the Power button (). Hp Officejet H470 Troubleshooting

I tried the reset suggested in the answers above by pressing the two buttons on the left, the "x" button and the "resume" button, simultaneously for ten seconds. Disconnect the power cord from the back of the product. caution: Only remove or install cartridges when the carriage stops moving. http://domcached.com/hp-officejet/hp-k7100-error-lights.html Solution one: Wait for the paper to dry Wait for the paper to dry.

Clean cotton swabs or any soft, lint-free material that will not stick to the cartridges (coffee filters work well). Hp Officejet H470 Blinking Orange Light If the carriage is stuck in the middle of the product, move the carriage to the right side of the product. Figure : Open the cover on the product Lift the cartridge cover, and then gently pull the tri-color cartridge up and out of the slot.

Open HP Solution Center: Windows XP: On the Windows taskbar, click Start, click All Programs, point to HP, and then click HP Solution Center.

Issue: The Power light is on and the Right and Left Cartridge lights blink The Power light is on and the Right and Left Cartridge lights blink. Wait for the carriage to stop moving. caution: Remove the paper carefully. Hp Officejet H470 Won't Print I cannot find the above error light pattern in the online troubleshooting tips.

Close the cartridge cover to secure the cartridge into place. Videos English Open Menu English Deutsch Español Français Português 中文 한국어 † The opinions expressed above are the personal opinions of the authors, not of HP. Close the cover on the product. http://domcached.com/hp-officejet/hp-k8600-error-lights.html The printer is now reset.Sometimes a replacement procedure has a reset procedure as part of it, the manual does not spell out the replacement procedure, it just says follow the instructions

Thanks for trying. note: Check to make sure the part number of the ink service module replacement kit is correct for your product. Carefully remove all traces of paper that you can find. Figure 8: Press and slide the notch with a screwdriver Figure 9: Remove the ink service module Remove the new ink service module from the packaging.

The ink service module is located on the bottom of the product.Press and slide the notch with a screwdriver, and rotate the ink service module to the left to remove it.Remove Showing results for  Search instead for  Do you mean  or Post new question Post new question Question Reply Topic Options Subscribe Mark Topic as New Mark Topic as Read Float this If the paper tears, part of it might remain inside the paper path and damage the product. Figure 41: Remove the cartridges If there is tape on either of the cartridges, remove it.

Solutions IMPORTANT: Follow these solutions in the order presented to resolve the issue. Adjust the paper width guide so that it fits snugly against the paper. I am an employee of Hewlett Packard.- - Please mark Accept As Solution if it solves your problem so others can more easily find the answer - -- - Please click Reply 0 0 kathy-n Student Posts: 1 Member Since: ‎09-28-2014 Message 5 of 5 (1,990 Views) Report Inappropriate Content Re: Officejet H470 won't print - error light blink pattern not in