The SW onlyoffers print to Com1, Com3, file, or LPT1. My cartriges are fairly new and have plenty of ink. Dr. by dimmers on Sep 16, 2005 at 3:14pm Add comment Please sign in to comment 1 That's normally a bad LIU, (Line Interface Unit), that's the module the phone plugs in Source
Comment Was this review helpful to you? by Carol CPA on Jun 3, 2005 at 12:58pm Add comment Please sign in to comment Carol CPAThe problem could be the fax module assembly. by Mike on Feb 13, 2004 at 11:53am Add comment Please sign in to comment 0 Ken: The G85 uses a Power Module Assembly [part # 0950-2880] with a separate Power used torx10 to take off cover (just was careful and went in through front), pulled electrical connector and off it came. http://support.hp.com/us-en/document/c00034909
Hp Officejet G85 Troubleshooting
Have tried to get both parts (have HP part number) but no success. by Bert on Apr 1, 2004 at 10:03pm Add comment Please sign in to comment 0 JG by Anonymous on Apr 7, 2004 at 5:48am Add comment Please sign in to Cause of Error: Internal system conflict. It combines the three functions I need: flat bed scanner, fax, and color printer. 3.
The mechanism that lifts it won't engage to lift it up when you go to print, copy, scan, etc.It'll try a few times, and then give the out of paper problem.This To remove the LIU, remove the T20 Torx screw on the left, as viewed from the rear, and the LIU and its cover can be easily removed. Swapped them back and the printer complained again. Then power it up again.
It’s the mother of all messes when they run over, better to clean it before this happens. Hp Officejet G85 Manual C00F0401 . Remove the screw in the vertical frame to the right of the carriage drive motor. 5. http://www.fixyourownprinter.com/posts/24081 Any suggestions as to what is wrong and where to buy replacement parts online?
Do you think I should (1) have the work done, (2) buy the parts and do the work myself (I have no experience with repairing such units but am fairly mechanical) Cables Removing the rear panel will reveal some cables connected to the scanner. by Bert on Mar 10, 2004 at 10:09am Add comment Please sign in to comment I keep getting two messages on my printer telling me that "Error: Incorrect color cartrige installed" How do you get to this underside?
Hp Officejet G85 Manual
Once again many thank. http://www.fixyourownprinter.com/posts/16440 if not where does it go? Hp Officejet G85 Troubleshooting Your fix for the HPG85 error code C00F0401 worked PERFECTLY!!! I notice that there's now a different part number assigned to the duplexer.
HP has been messing with their web site and managed to break things. this contact form reassembled/tested. IBM WebSphere Portal Home IBM Logo Sign Up Log In Welcome Getting Started Contact HP - Anonymous Contact HP Product Context View Support Home Test page Product Home Product Warranty Result Rachel T.
Make sure you take your fingers off immediately when the display first starts. Can anyone help me?Thank you so much in advance!Kristin Respond to this 0 Do This FirstPress and hold buttons 6 and # while plugging in the power. by Bert on Jun 4, 2004 at 9:23pm Add comment Please sign in to comment 0 Thanks for the quick response.
And only ONE MORE TRY and it WORKED!
Disclaimer The steps given below need to be followed under supervision of a Technical Expert. The fax has a memory of 100 pages and easy speed dialing of 100 numbers. I think it is the paper sensor. Removing the Scanner Tilt the scanner upward as if you are going to access the cartridges.
I'm glad I ws able to save my printer. Now that I have a brand new IBM Laptop with Windows XP, it does not. Thanks again! Check This Out Please try again Report abuse 3.0 out of 5 starsBetter printer than the software that comes with it By A Customer on October 16, 2001 The printer performs more or less
Thank you for your feedback. This will allow you to remove the LIU (Line Interface Unit) cover and unplug the LIU. Ask the community! I recommend latex gloves if you want to avoid getting ink on your hands once the case has been removed. 1.
My husband said that he can get the fax working if he shuts it down but after the first fax, we have to manually do it. The 6 + # thing worked a treat, but only on my umpteenth attempt! by unknown on Apr 27, 2004 at 10:25am Add comment Please sign in to comment 0 I keep getting a scanner failure error. See the 5/12/2004 12:38:34 post in this thread to remove the case.
It will hinge upward. This will allow you to remove the LIU (Line Interface Unit) cover and unplug the LIU. I have had this printer for many years obviously and paid a small fortune for it when new. This is not good, because this printer's LPT1cable appears to be a rare item and the connector for LPT1 on the printer's side is subjectto too much leverage - which can
It doesn't happen all the time and and sometimes not until after the print job has started. The part number is C6426-40001.Any direction would be appreciated.