Align the cartridge with its color-coded slot, and then insert it into the slot. If pieces of paper remain inside the product, more paper jams are likely to occur.Reach inside the product, and then manually move the carriage. I had also disconnected the power (which I forgot to mention) but only for a few seconds. Close the top cover. http://domcached.com/hp-officejet/hp-k7100-error-lights.html
If the error message no longer displays on the computer, you do not need to continue troubleshooting. I guess you have my E-mail address, [emailprotected]. Press the Power button () to turn on the product, if it does not turn on automatically. Figure : Example of the estimated ink levels graphic If one or more of the cartridges are low on ink, consider replacing the cartridges.
Hp Officejet Pro K5400 Troubleshooting
Press the Cancel button () once. When I returned the blue ink cartridge indicator light was blinking and... I'm awaiting the "service mode reset procedure".
Disconnect the power cord from the rear of the product. Use both hands to pull whole sheets of paper to avoid tearing them. I can't budge it. Hp Officejet Pro K5400 Power Light Keeps Blinking Wiedergabeliste Warteschlange __count__/__total__ Fixing a Paper Jam - HP Officejet Pro K5400 Printer justprintingaround AbonnierenAbonniertAbo beenden3.9283 Tsd.
After doing these prints in each color, try a highlevel (level 3) cleaning. Hp Officejet Pro K5400 Clean Print Heads Method one: Clean the paper rollers through the rear access door Gather the following materials: A clean, lint-free cloth, or any cloth that will not come apart or leave fibers Distilled, Push the latch handles on the door inward, and then pull the door toward you to remove it. Step one: Check for missing cartridges Open the cartridge door, and then check if one or both of the cartridges are missing.
Disconnect the USB cable or the Ethernet cable from the rear of the product, depending on your connection type. Hp Officejet Pro K5400 Ink Press the Power button () to turn on the product. Close the top cover. NOTE: Ink level warnings and indicators provide estimates for planning purposes only.
They can get moisture and soiled too- check all doors/flaps and back panel/duplexer are in position- check that sensor/switch closing plastic parts (like on the cartridge door) haven't broken off stopping
Anonymous Jan 16, 2009 I have the same problem, if you can help, cuold you send a msg here:firstname.lastname@example.org.Thanks.
Solution one: Load paper Follow these steps to load paper if the product has run out of paper.
Wait for the product to initialize the printheads and print an alignment page.
Hp Officejet Pro K5400 Clean Print Heads
Insert the door into the rear of the product, and then gently push it forward until it snaps into place.
Figure 21: Slide the paper guides inward Lower the output tray. Hp Officejet Pro K5400 Troubleshooting Any other ideas on how I can unlock the carriage? Hp Officejet Pro K5400 Manual Close the top cover.
Solution two: Remove and reinsert the printhead Improper printhead placement or installation might cause a printhead error. http://domcached.com/hp-officejet/hp-deskjet-460-error-lights.html Close the printhead latch. Unplug the power cord from the wall outlet. I agree with a fellow poster that putting back the original printheads is a worthwhile experiment. Hp K5400 Clean Print Heads
Solution four: Service the printer If you have completed all the steps listed above and are still experiencing a problem, continue to the Service the printer section at the end of Solution two: Remove and reinsert the printhead Improper placement or installation of the printhead might cause a printhead error. If the print quality is worse near the start of the print movement, or you get fairly random artifacts, I'd be more inclined to think the cartridge itself is depositing ink http://domcached.com/hp-officejet/hp-k8600-error-lights.html Wait at least 15 seconds.
If the product does not turn on by itself, press the Power button () to turn it on. Hp Officejet Pro K5400 Printer Since there has been no resolution to the problem, I cannot accept your answer nor agree to payment. Rotate the rollers as you clean them to make sure they are clean all the way around.
Disconnect the USB cable or the Ethernet cable from the rear of the product, depending on your connection type.
Figure 56: Insert the cartridge and close the cartridge door If these steps resolved the issue, you do not need to continue troubleshooting. Step six: Print a self-test page Make sure that plain white paper is loaded in the input tray. Close the printhead latch. Hp K5400 Drivers Press down firmly on the printhead to ensure proper contact.
Step two: Print a self-test page Print a self-test page to make sure that the product functions correctly. If the issue persists, continue with the next solution. Apply a moderate amount of pressure to remove dust or dirt buildup. http://domcached.com/hp-officejet/hp-h470-error-lights.html NOTE: The product might go through a warm-up period of up to two minutes.
How to print a self-test page Make sure that plain white paper is loaded in the input tray. Figure 62: Insert the cartridge and close the cartridge door Issue: The Power light and one or more Print Cartridge lights blink In this error condition, the following light pattern displays Press the Cancel button () once. Reconnect the power cord to the rear of the product.