Home > Hp Laserjet > Hp Laserjet Iip Error 55

Hp Laserjet Iip Error 55

Replace Laser/Scanning assembly. 51.X Error Cycle 5Si/4000/4050/4100/5000/8000/8100 Only: A laser subsystem problem exists. 1. Sign Up Login Add Question unknown asked May 17, 2001 at 4:10pm 0 Unknown Printer HP IIP error 55; then 79-09ae My HP LaserJet IIp gives an error 55 on power Check these items. Power Supply (P/N RG1-0906- 000). http://domcached.com/hp-laserjet/hp-laserjet-57-service.html

IIISi/4Si check the door open sensor flag, PS1. For example, 1 = fan motor 1. In rare instances the ac power supply has failed. This problem can be caused by software/drivers, memory PCA's, font macro personality cartridges, or optional I/O cards. 2. over here

Some of the checkpoints referred to in this document require special tools or meters as well as familiarity and training on laser printers. It is possible that the formatter is responsible for both of your problems. Check SW101 to make sure it is engaged with top cover closed.

Simplify the print job, reduce the dpi setting or install additional memory. Replace Formatter PCA. 3. Check connections to DC controller - replace main motor 4L/4 Main motor problem, check gear train for binding. Could also be a failure of the power supply. 4L/4P/5L/5P/6L/6P most likely cause is a bad ceramic heating element.

Also verify the configuration through the menus on the printer. Check I/O and replace if req'd 24 Job memory full Add more internal printer memory or simplify the print job 25 xxx Mem full All printers Add more internal printer memory Replace Scanner Assembly. https://www.fixyourownprinter.com/posts/1000159 Replace MIO card. 3.

If the problem continues, remove the optional interface card and set the printer for standard parallel interface by taking off-line and holding down "Menu" key for 5-10 seconds. II, IID, III, IIID Replace registration assy. Remove any accessories (font cartridges, memory PCA's, SIMMs, etc.) plugged into the formatter card and try again. IIISi/4Si 1.

Firmware updates are available for some machines at http://hp.com and clicking on the drivers and software tab. https://www.experts-exchange.com/questions/10332608/HP-Laserjet-IIP-55-error.html Error 23 I/O Not Ready I/O card can't accept data or isn't connected to the network. Pretty rare though. On the 3Si/4Si a command was sent to print envelopes while the printer was in duplex mode.

Inspect toner level sensor connector for damage. 4. http://domcached.com/hp-laserjet/hp-laserjet-6p-repair.html Replace AC Power Module. 3. Replace cable, fuser to DC Controller (P/N RG1-0907-000) II, IID, III, IIID Only: 1. If the connections are good and the problem persists, the unit is good only for its parts. 0 Message Author Comment by:wavking2000-04-25 Comment Utility Permalink(# a2749082) That's what I was

Turn the image adapt and page protect to ON or AUTO either from the control panel or from within HP Explorers Remote Control Panel. 5P/5Si Same as above, Press GO to Check pickup rollers and separation pad clean as needed. I will have purchasing call in an order. Check This Out All other printers, replace laser scanner assembly.

Defective Formatter PCA - Replace with known operational board and try again. Remove and reinstall the supply, replace the supply. Back back to top How did we do?

Replace formatter PCA. 60, 61, 63 MEMORY ERROR IIISi/4Si Only: 1.

Replace Formatter PCA. 4. May not be connected - check cabling - or it may be defective. Worn pick up rollers and/or separation pad. This can generally get you 100 or so more pages.

Bad or dirty cartridge contacts. Check that ROMs are in correct location and orientation. 3. Replace memory PCB 53-2 - Error in rear memory slot. this contact form Top cover open. 2.

Printer got tired of waiting for user interaction like a manual feed. Help! Replace the fan. IIISi, 4Si, LJ4, 4+, 4P Install toner cartridge Check tabs on right side of cartridge. (Need at lest one tab) Switch actuator bent, support tab in upper right corner of DC

Same as error 51. Resolve same Damaged fiber optic cable. Cycle power. 4. Check entire paper path, check all sensors and flags. 13.21/13.33 Door open jam. 8000/8100 Only: 13.1 Paper late jam at PS2. 13.2 Paper delay jam at PS1 13.5 Fuser output, paper

Bad paper exit sensor. Recycle printer power. Error 58 4/4L/4P/4V/5/5P Check the fan cable - reseat cable or replace fan 4V/4MV Defective DC controller board - replace IIISi/4Si Error 58.1 & 58.2 Improperly seated paper cassette 4Si/IIISi 58.1/58.2 Defective Internal Memory - Replace the Formatter PCA.

Paper size selection doesn't match the paper being used. Press continue or go on the printer to clear message. Same as error 51 2686A/D Bad scanner assembly II, IID, III, IIID Bad cable laser/scanner to DC controller PCB Replace laser/scanner assembly IIP, IIP+, IIIP Bad scanner motor Bad DC controller Back back to top How did we do?

Replace main motor.