As you can see we are not just another computer-products mega-website! Veronica Casto Houston, TX It is nice to place anonline order & get to talk to an actual person. Verify that the tabs aren't damaged and that the tray switches located in the printer are not damaged. Remove the printer from any UPS supplies, additional power supplies, or power strips. 2. http://domcached.com/hp-laserjet/hp-laserjet-57-service.html
What to do:Where possible, try connecting to a different port on the computer. In some instances, electrical noise in the cable can corrupt data during transmission to the printer. If this is successful, you have a problem with the optional I/O card and should replace it or reset it. You can remedy this by replacing the paper guide plate assembly, RG5-2248-030.
A buildup of toner on the edges of the tray which slide into the printer can sometimes cause problems.
Defective formatter board. 3.
Back Error 11 - Paper Out Paper tray empty or not seated correctly.
Contact HP support: www.hp.com/go/support 55.0601 DC controller NVRAM data error Turn the printer off, and on again. Simplify the job by removing font changes etc. All fans are enabled to low speed operation at power on. 59.f0 Error Hp Printer Check the HP paper specification guide for more info.
X = Description 4 Printer Fan 7 Duplex Fan 1. ERROR 43 / ERROR 43 OPT INTERFACE This indicates a communication problem between the formatter PCA and an optional interface installed (such as a network card). Verify the environmental thermistor cable is securely connected. 3. original site What to do:Try simply reseating the memory chips.
This pad needs to provide friction to the feeding paper. 52 Scanner Error M521dn A printer command error has occurred. If the problem persists and is application specific, verify proper setup with application vendor. Any error messages displaying on the printer or computer?
50.0 Fuser Error Hp Laserjet P1102
Paper jams can occur at four stages: pickup, printing, fusing and exit. http://support.hp.com/vn-en/document/c05049258 We help people fix printers. 52 Scanner Error Hp Laserjet If the firmware should become corrupted or fail (usually because of an interruption when attempting to update the firmware), the product will no longer function. 50.0 Fuser Error Hp Laserjet P1108 What to do:First of all try resetting the printer by turning it on and off.
If the error persists, the engine control PCA needs to be replaced. http://domcached.com/hp-laserjet/hp-laserjet-6p-repair.html Replace or clean as needed. What to do:These faults typically needed assistance from an experienced HP engineer. Join Us! *Tek-Tips's functionality depends on members receiving e-mail. 50.0 Fuser Error Hp Laserjet P1007
Disconnect the power cable from the product, wait at least 30 seconds, then reconnect the power cable and wait for the product to initialize.2. Communication error between printer and the controller. 3. controller board 6. have a peek here The event is 98.02.01 and the description is [[cELPartnMgrWipePartNotFoundError]]Thank you Reply 0 0 VisionAiry Distinguished Professor Posts: 3,396 Member Since: 02-15-2013 Message 4 of 16 (54,751 Views) Report Inappropriate Content Re:
HP LASER PRINTER 5000, 5100 1. 50 Fuser Error Hp Laserjet 3050 Event code Description Recommended action 55.0005 Hardware memory error (DC controller) The engine control PCA needs to be replaced. If this doesn't solve the problem then replace the dimms and then the formatter board.
X description: 0 = Motor error 1 = Motor startup error 2 = Motor rotation error 1.
Remove the printer from any UPS supplies, additional power supplies, or power strips. 2. Check the cabling to the ECU. Perform an engine test. 4. 52.00 Error Hp Laserjet 2420 Printer below there was two wheels for the unit to roll.
What to do:You need to reduce the size of your print job. I/O configuration for the computer or printer is incorrect. Get in touch with us HP LaserJet Printer Error Codes If your HP LaserJet printer has stopped working then it will probably also display an error message. Check This Out HP Error Code:66 - External Paper Handling Device Error Explanation:This fault means there's a problem with one or more additional paper or envelope trays or finishing units, such as a staple
You may need to have your printer serviced. Replace this as an assembly. Loose or bad cable. 3. If unresolved the formatter board may need replacing.
Can also indicate a mis feed or paper not being picked up. A broken tooth on one gear is all it takes.