Home > Hp Laserjet > Hp Laserjet 6p Problem

Hp Laserjet 6p Problem

by moe on Feb 18, 2007 at 4:09pm Add comment Please sign in to comment "I did manage to get the printer to pull some paper in by manually "helping"it. will help you or not. Maybe you posted before you saw my last response. These Aren't Roasted! Source

The part that puzzles me is that your motor is turning. troubleshooting ir printing problemspage 127................................................................................................................................................................ The third round, the amber error light remains solid instead of blink. Oct 17, 2005 9:35 AM Helpful (0) Reply options Link to this post by Anthony Thomas, Anthony Thomas Oct 18, 2005 7:03 AM in response to greg sahli Level 1 (25 check that

Any ideas? 3 replies 34 have this problem 7 views Last reply by aglloyd 5 years ago Nels7 Posted 3/7/11, 7:52 AM When I print from a website, the information comes When I print from a website, the information comes out garbled. That printer rarely gives me any problems in Windows. I even put a piece of paper in the path up until it would go out the last roller.

Perhaps the Laserjet 6P has a memory problem? 0 #3 John Hook Posted 15 April 2008 - 09:39 PM John Hook Member Member 165 posts Ztruker, I've seen this problem before Have you ever tried the printer with Windows to know if it works correctly with that? The green ready light quits blinking. Oct 18, 2005 7:03 AM Helpful (0) Reply options Link to this post Apple Footer This site contains user submitted content, comments and opinions and is for informational purposes only.

The person throwing it out couldn't tell me any specifics other than it just "quit working". Troubleshootingpage 62................................................................................................................................................................ With (2), I could override this with an service adjustment program or by resetting the cartridge to think its full if I wanted to do. his comment is here There is also a black round wheel with rubber around it on the left-hand side that will turn.

help any1? When the printer is finished with its initial checks, the solid amber light is the only one that remains lit and stays on, but at least it looks like I didn't Do you wish to proceed to the home page of the new product? Don't show me this message again.

Sorry for the disappointing opinion, but facts are facts. http://www.tomshardware.com/forum/62239-3-problem-printing-laserjet-printer I think one of the 2 models 5P/6P had a hole in the formatter you could stick something into to actuate the button, the other didn't. Once registered and logged in, you will be able to create topics, post replies to existing threads, give reputation to your fellow members, get your own private messenger, post status updates, I didn't ask where they were.

Then I went into the printer properties and disabled spooling so I print directly to the printer, still no change. this contact form When I press the JOB CANCEL or GO button, the solid amber light goes off, and the green ready light blinks 8 or 9 times. If so why does manualy pushing the paper in the printer until the wheels do take it not make the error light go off?I tried again to get that formatter off, If you know of any other things to try, please let me know.

  1. I cannot find a driver that makes this possible.
  2. It's basically the same engine as the 6P with all the same sensors, and most parts are interchangeable.
  3. Even so it is still in place so the printer should sense that the cartridge is at least in place.
  4. Sorry if that part was not clear.
  5. Until I can get the light off that doesn't seem to matter and may not be needed anyway.I am guessing that if this isn't it, that I have pretty much exhaused
  6. Cancel Subscribe to feed Question details System Details Windows Vista Firefox 4.0b12 More system details Additional System Details This happened Every time Firefox opened This started when...
  7. It should be a recoverable error according to the manual.
  8. Please wait while we process your request.
  9. I know the other lights are working because the initially flash on when the printer starts.

USe the HP Laserjet 6 Series, Gimp-Print driver because I don't think your printer is postscript. All the lights will light up. It doesn't look like that "D" piece could rotate forward or back without breaking something even when I temporarily rotate the "clutch?" out of the way.It recognizes the cover is shut have a peek here I looked for anything out of the ordinary..

XP found and installed the driver, but when I print to it, it spools, I see the pages building up (10 all together), the printer light flashes as if it's going After installation is done, go to the folder Downloads/hplip-3.12.6 - Run in terminal : $ cd ~/Downloads/hplip-3.12.6 $ ./configure --prefix=/usr --enable-pp-build $ make $ sudo make install - After this, connect Finally got the screws out with some needle nose pliers and some force.

It engages with a white plastic wheel on tray 1 which is also moving.

In the properties for the "ECP Printer Port" device, go to "Port Setting" and use the "Never use an interrupt" setting. I have fixed other electronic stuff on their way out to a dumpster too because I know some stuff to try that other people don't. The product could not be added to your profile at this time. How likely would that be?

I'm still hung up on the lights since most times it is the amber, but once you said the light next to it was also on after an attempted cold reset. The following checklist will help determine the source of the problem. 1. I only see links for a a 6L so I still have looked for the closest I could find although I am looking through the numbers now too.I wish I knew http://domcached.com/hp-laserjet/hp-laserjet-1015-problem.html Simply stated, if you hear the motor running on startup, it's not the fuser sensor.

If you continue to have problems printing using the IR port, contact the manufacturer or dealer where you purchased your portable device to verify compatibility with the IrDA standard, and follow The steady amber error light returns.Is it something to do with the paper pickup assembly? There may be a bunch of other stuff that needs replacing, and a test print might give me a better idea. I got an personal email reponse from Sarbeswar Meher at Launchpad with the following information: There are lots of dependencies missing which is shown by 'hp-check'.

Any chance this could be caused by bad ram in the printer itself? United States Copyright © Apple Inc. I request you install the latest hplip from http://hplipopensource.com/hplip-web/install/install/index.html and follow the instructions from their website. If you change the BIOS settings, I've found that you need to go into Device Manager, DELETE the parallel port device and let windows re-detect and re-install the driver.

Any other suggestions as to what may be wrong? Sometimes it really is a simple fix including stuff that's even covered in the user's manuals! Is it possible that it just doesn't recognize the toner cartridge itself? While the green ready light is blinking those 8 or 9 times, the large white plastic wheel with gears on the left side of the printer is moving.

but I think I'm gonna move on and stick with linux mint from now on... Last edited by cornelis spronk; July 5th, 2012 at 10:54 PM. You really need to remove the formatter and somehow you have to get those screws off, either with a special tool or drilling out.