Home > Hp Laserjet > Hp Laserjet 5m Error 51

Hp Laserjet 5m Error 51

That QA sticker, I think was yellow graphics on green, and it's usually on top of the black box that contains the wiring connections. Make sure fuser is correctly seated to AC Power PCA. 2. controller. A temporary printing error has occurred. 2. http://domcached.com/hp-laserjet/hp-laserjet-57-service.html

Personality cartridge installed in font slot is incompatible with printer. 72 SERVICE 1. Laser scanner assembly not seated. 3. Replace DC Controller PCA. 2. Defective DC controller. 4.

Press GO. You can likewise take a look at my Tumblr blog when you have your complimentary time.Have an excellent day my good friend! Turn the printer off, and then turn the printer on. 2. Duplex mechanism has failed 70-71 ERROR 1.

  • Remove EIO cards, perform cold reset 6.
  • This error indicate that loss of beam-detect occurred. 51.10: Beam-detect error 51.20: Laser error Solution 1: Dowload the last version of the driver Solution 2: Press the "go" button.
  • Clean the optics with a soft brush or lens tissue.
  • Computer and printer may be set to different baud rates. 2.
  • Sensor arm stuck or broken. 12 PRINTER OPEN 1.
  • or its affiliates.

The part of the top door that pushes the Plunger down is broken. 13 PAPER JAM 2686 Only: 1. The cause is a bad cable between the DC Controller and the laser/scanner assy. Conection has been broken between printer and EIO/MIO card; try reseating EIO/MIO card 40.X Mio Error 5Si Only: 40.1 HP Mio port 1 (upper slot) 40.2 HP Mio port 2 (lower Check Fan 1, replace if necessary. 57.3 ERROR 1.

Check connectors J204 and J6 on DC Controller and conenctor at Fan 1. 2. Replace AC Power Module. 3. HP LASER PRINTERS 3015/3020/3030MFP 1. https://groups.google.com/d/msg/comp.sys.hp.hardware/1isoKgwwlFw/Y9ttgaJgY7EJ Printers problem solving,tips, tricks and tutorial.

DC Power Supply malfunction. 2686 Only: 1. HP LASER PRINTER 3050, 3052, 3055, 3390, 3392 1. Keep up the good work mate and I promise to visit your site more typically. Check that PS1 is blocked by the latch flag.

controller3. http://www.printertechs.com/printer-troubleshooting/hp-error-codes/195-numeric-error-codes-50-59-hp-laserjet Please check out my web site as well and tell me how you feel. Controller. You may have to register before you can post: click the register link above to proceed.

Note IIISi/4Si: Short cp005 on DC Controller to bypass Error 50 time delay. (The printer must be turned off.) 5Si/4000/4050/4100/5000/8000/8100 Only: The fuser is malfunctioning. 50.1 Fuser low temperature failure. 50.2 this contact form HP LASER PRINTERS 5000, 5100 1. X description: 1 = Beam-detect error 2 = Laser error 1. Replace DC Controller. IIISi/4Si Only: Visually check or replace toner cartridge.

Top cover open. 2. Replace the scanner ass'yHP COLOR LASER PRINTER 4600, 5500 ERROR 51.1, 51.21. Check front panel settings. 3. have a peek here Temporary laser ass'y error.Turn printer on and off 2.

At least one of two tabs must be present. 3. Reply 0 Reply 0 0 Everyone's Tags: EBCOMMIPG View All (1) davidzuts Regents Professor Posts: 4,888 Member Since: ‎01-17-2009 Message 2 of 10 (19,171 Views) Report Inappropriate Content Re: HP M602 Reseat the connectors between the laser/scanner and the DC controller PCA (J83 and J84) 4.

Replace Duplex unit. 54.1 Remove sealing tape - 4100 only: Toner cartridge has been installed without removing sealing tape 54.4 error - 4100 only: Problem exists with customers line voltage 55

Replace Paper Control PCA (Solenoid/Sensor PCB Assembly). 4. Goldwasser. Does the scanner motor rotate? Replace fuser.

Replace the environmental thermistor. 4. Replace MIO card. 3. The line voltage and current source at the printer location might need to be inspected to ensure that it meets the printer’s electrical specifications. 51.X PRINTER ERROR A loss of beam-detect http://domcached.com/hp-laserjet/hp-laserjet-6p-repair.html Our quality is highly regarded due to our constant testing and attention to detail.We sell a wide variety of maintenance kits and parts, meticulously refurbished printers, and high-quality toner cartridges.

Defective toner cartridge. 2. IIISi/4Si Only: 1. Note IIP, IIP+, IIIP: Short C212 on the DC Controller to bypass error 50 time delay. (The printer must be turned off.) IIISi/4Si Only: 1. Hewlett Packard, in the last few years has been known to cut corners and not do enough research before entering products into the market place.

Reply With Quote 01-27-2015,02:51 AM #6 Silken Path View Profile View Forum Posts Private Message Member Join Date Jun 2014 Location Madison, Georgia Posts 921 Mensch, that's hilarious! On older style printers this is often caused by a bad main motor. (Older style printer being printers with halogen heating elements in the fuser - 4, 4+, 5, 4si, 5si, Today: I turned the printer on to print. I think what you found was the inspector's quality control sticker that was on top of the black box.

Kevin Find well displayed printer parts diagrams at: http://www.printerworks.com/ Share this:TweetShare on TumblrPrintRelated posts:Light Print - HP Laserjet Printer 4, 4+, 5, 5N Laser Scanner Repair Light Print -Laser Scanner Repair If it is not within the proper range, replace the fuser. IIISi/4Si Only: 1. Plug the printer into a wall outlet and see if this resolves the problem. 3.

See Service Note 33471-01B if Serial No. Remove optional I/O PCA, then re-test. 69.x SERVICE 4000/4050/4100/5000/8000/8100 1. Replace laser scanner ass'y.3. Replace DC Controller PCA. 2686 Only: 1.

a. No IR light now, time to replace the fiber. Turn on, and try to print a test page - which will fail.