Home > Hp Laserjet > Hp Laserjet 5100 Troubleshooting

Hp Laserjet 5100 Troubleshooting

The cover and Tray 1 will separate from each other. WARNING! Be careful when cleaning around the fusing assembly area. Page 169: Power Inlet Assembly Power inlet assembly Remove the top cover (see page 115) and the right side cover (page 123). Source

Then enter the IP address of the LJ5100 and set the Protocol to HP Jetdirect-Socket. Page 134 Top margin adjustment After replacing the paper-handling PCA, readjust the top margin. Page 157: Paper Guide Paper guide Lift the green handle (callout 1) in the middle of the registration assembly. This allows printer status, command, and dot-image data to be passed between the two PCAs. useful source

The product could not be added to your profile at this time. Facing the back of the printer, remove the two machine screws (callout 1) that hold the fuser in the chassis. Fusers are a consumable part and are sold as part of a maintenance kit; it is expected over the life of the printer you will replace the fuser several times. Page 102: Paper Jam In The Duplexer Figure 32.

Facing the left side of the printer, orient the shaft so that the open end of the shaft (callout 3) points away from the solenoid arm. Table 29. Page 74: Power Supply System, Ac/dc Power Distribution Power supply system Ac/dc power distribution The ac line voltage for the printer is applied through the main switch (SW101) and supplied to Page 94: Clutches And Sensors, Printing From Tray 1, Printing From Tray Tray 1 feed roller.

Please type your message and try again.            martí ferré Level 1 (0 points) Q: Problems with HP LaserJet 5100 With the latest system actualization ( OS X Yosemite 10.10.4) If white spots appear on the black strip, create a cleaning page again. If the requested paper size or type is not available, the printer asks if it should use another paper size or type instead. http://support.hp.com/us-en/product/hp-laserjet-5100-printer-series/74341/troubleshooting Page 13 Figure 139.

Q1860-90918 Chapter 3 Printer operation 49 www.GovTechMedia.com... You will be taken to the Adobe site to download the reader. Jul 7, 2015 2:43 AM Helpful (0) Reply options Link to this post by PAHU,★Helpful PAHU Jul 7, 2015 4:32 AM in response to martí ferré Level 6 (16,630 points) Jul Note Callout 1 in figure 101 shows a detail of the separation pad.

The printer has the following three protection functions to prevent incorrect activation of the fusing-roller heater. https://discussions.apple.com/thread/7117038?start=0&tstart=0 Facing the left side of the printer, insert a flat-blade screwdriver and twist gently to release the tab on the left side of the delivery roller (callout 1). Pro Slate 12) OR Browse all HP products Please wait while we process your request. Page 2 www.GovTechMedia.com...

See the software help for more information.) If the message persists, increase the amount of RAM installed in the printer and the size of the RAM disk. this contact form Page 171: Pickup Roller Figure 103. The delivery assembly is secured by three tabs on each side. Use the flat-blade screwdriver to press down the two locking tabs (callout 3) on the top of the front cover (callout 4) and then remove the front cover by reaching under

Page 99: Paper Jam Paper jam To detect the presence of paper and whether the paper has been correctly fed, the following paper sensors are installed: Registration roller paper sensor (PS403) More Support Options Related Videos - of Video Tutorials | Show all Show less HP Download and Install Assistant HP Download and Install Assistant makes it easy to download and install These are long screws; their position requires the use of a magnetized screwdriver. http://domcached.com/hp-laserjet/hp-laserjet-5si-troubleshooting.html Q1860-90918 www.GovTechMedia.com...

Page 187: Troubleshooting Process Flow Q1860-90918 www.GovTechMedia.com For error messages See “Printer encountered printing messages” on the event log, see page 193 to printer messages. Z7_3054ICK0KGTE30AQO5O3KA3070 hp-promotion-tiles-portlet Actions ${title} Loading... The shaft of the engagement arm fits through a molded plastic ring on the left side of the top cover.

Configure the printer according to your printing needs.

  1. CAUTION Performing a cold reset resets the Jetdirect and other EIO configurations.
  2. These two fonts are not available at the same time.
  3. Remove the screw, and then lift off the cover.
  4. They provide automatic I/O switching between multiple computers or networks connected to the printer.
  5. Slide a small flat-blade screwdriver along the outside edge of the control panel overlay to disengage the two tabs on the outside of the cover.
  6. Figure 84.
  7. The paper passes through the registration roller paper sensor (PS403) and stops at the registration roller that is not turning, momentarily stopping the leading edge of the paper and correcting its
  8. Thank you!
  9. Check the printer software for supported sizes.
  10. Turning PowerSave off is not recommended.

Page 131 Note The transfer roller is held on the right side by a hinged clip (callout 3; also see callout 4 in figure 59). Release the guide by freeing the end pins (callout 2), and then lift the paper guide out. The system returned: (22) Invalid argument The remote host or network may be down. Printer dimensions—HP LaserJet 5100 printer and HP LaserJet 5100Le printer Q1860-90918 www.GovTechMedia.com 139.8 cm (55 in) 62.5 cm (24.6 in) 47.0 cm (18.5 in) 27.0 cm (10.6 in) 47.0 cm (18.5

Figure 59. Page 70: Preventive Maintenance, Reset Maintenance Count, Expected Life Of Components After the printer maintenance kit has been installed, reset the maintenance count. Remove the control panel from the top cover (see page 117). Check This Out Page 114: Parts Removal Order Parts removal order Use the following diagram to determine which parts must be removed before removing other parts: Formatter assembly Front cover and tray 1 Left

Possible values Note For developers only. Page 183: Sheet Feeder Power Connector 500-sheet feeder power connector Remove the left cover from the 500-sheet feeder (see page 174). U.S. The EIO card might be defective. 1.

Page 66: System Configuration, Ms-dos System Configuration, Parallel Ms-dos Commands, Printer I/o Configuration, Parallel Menu MODE LPT1:,,B Note This example assumes that you are using parallel printer port LPT1. Page 103: Basic Sequence Of Operation The formatter PCA and the dc controller board share information over a serial data bus. Page 52: Print-quality Menu Print-quality menu Some items in this menu can be opened from a software application, or from the printer driver (if the appropriate driver is installed). Sign-in Register Site help Skip to ContentSkip to FooterLaptops & tablets Business Premium Gaming Standard laptops Workstations Convertibles & detachables Tablets 3-in-1 Desktops Business Immersive Gaming Towers Workstations All-in-ones 3-in-1 Printers

The product could not be added to your profile at this time. Apple may provide or recommend responses as a possible solution based on the information provided; every potential issue may involve several factors not detailed in the conversations captured in an electronic Dc controller assembly removal (2 of 3, long screws) Slide the dc controller assembly out of the rear of the chassis. This tool will detect HP PCs and HP printers.