Home > Hp Laserjet > Hp Laserjet 1300 Error Codes

Hp Laserjet 1300 Error Codes

Contents

ENWW Cleaning the equipment 45 Cleaning the print path Use this process if you discover toner specks or dots on printouts. re 86. If you do not want the printer to be in manual feed mode, change the setting from the printer properties. CNCD1 23456 Manufacturado Manufactured: February 10, 2003 Apparaten skall anslutas till jordat natuttag. Source

Overview of laser/scanner operation ENWW Printer functions 61 Power system on ECU The AC, DC, and high-voltage power supply circuits are all contained within the ECU. Printer unit functional block diagram 58 Figure 13. Check the paper path for toner or paper dust buildup. Wayne Haub Kansas City Help with HP printer problems and error codes. read this post here

Hp Laserjet 1300 Blinking Orange Light

re 85. Hewlett-Packard makes no warranty of any kind with respect to this information. Table 9. Also caused by the density adjusting PCA located behind the density adjusting slide switch.

that should clear the memory and give you a good view of the internals. You may have other rights which vary from state to state, province to province, and country/region to country/region. Plug the printer into a wall outlet and see if this resolves the problem. 2 If the printer is already plugged into a wall outlet, try another power source in the Hp Laserjet 1300 Manual Alcohol is flammable.

Veronica Casto Houston, TX It is nice to place anonline order & get to talk to an actual person. Replace damaged cords immediately. 5 Unplug this product from wall outlets before cleaning. 6 Do not install or use this product near water or when you are wet. 7 Install the Electrical components 197 Table 30. Defective toner cartridge in the Laserjet 4 Plus only.

r L. Hp Laserjet 1300 Cleaning Printed media is collected here in the correct sequence when the straight-through output door is closed. reconnected both ribbon cables4. Performance of HP LaserJet 1300 series printer 17 Table 6.

  1. Basic sequence of operation 71 Table 13.
  2. To maintain quality, thoroughly clean the printer: • Any time a new print cartridge is installed. • After printing approximately 2,500 pages. • Whenever print quality problems appear.
  3. CAUTION To prevent damage, do not expose the print cartridge to light.
  4. If the problem persists and is application specific, verify proper setup with application vendor.
  5. Load media with the top forward and the side to be printed facing up.
  6. The following systems are discussed: • formatter • printer functions • engine control unit (ECU) system/power system • image formation system • paper-feed system (printer) Figure 11.
  7. Your cache administrator is webmaster.
  8. On the LJ4/4M/4+/4M+ the sensor flag can get knocked out of place when a paper jam occurs and the tray is pulled out abruptly.
  9. Error 23 I/O Not Ready ALL PRINTERS The I/O card is not accepting data.
  10. re 59.

Hp Laserjet 1300 Software

Turn the printer off/on to attempt to clear or reset the message. http://www.all-laser.com/aerror-code/ It won't help. Hp Laserjet 1300 Blinking Orange Light Verify that the SIMMS or memory cards are seated. Hp Laserjet 1300 All Lights On re 65.

Again on the LJII/III we are starting to see more and more failures of the gear drive assembly. this contact form The main input tray can hold up to 250 sheets of 75 g/m 2 (20 lb) print media. Remove all EIO devices and firmware DIMM if installed. Make sure the paper cassettes are installed correctly and adjustments are set properly. Hp Laserjet 1300 Service Manual

The priority input tray can hold up to 1 sheets, one envelope, or one piece of heavy media. Please wait while we process your request. Regular labels my 'ooze' adhesive as they pass through the fuser assembly and literally gum up the works! http://domcached.com/hp-laserjet/hp-laserjet-1300-windows-7-error.html This guide is available in .pdf format online at http://www.hp.com/support/ljpaperquide .

Fuser assembly (220-240 V) RM1-0536-000CN 50,000 Can affect print quality and paper movement. * The estimated print cartridge life is based on letter- or A4-sized paper with an average of five Hp Laserjet 1300 Print Configuration Page See the user guide for more information. • Add more memory. Power cycle the printer.

Reseat the card and if available, swap with a known working card.

Back back to top How did we do? Firmware updates are available for some machines at http://hp.com and clicking on the drivers and software tab. Media types 33 Table 1 1 . Hp Laserjet 1300 Paper Jam Error 18 MIO Not Ready The printer is not connected to a LAN when it's expecting to see a LAN.

re 78. You should hear a definite clicking. Page complexity (ruling lines, complex graphics, or dense text) can exceed the printer's ability to create the page image fast enough to keep pace with the image formation process. Check This Out If it blinks without any job on the print queue then you have an hardware issue with the printer try putting the power out for abt 3mins also open the printer

re 67. As the mirror rotates, the beam reflects off the mirror, first through a set of focusing lenses, then off a mirror, and finally through a slot in the top of the The following steps occur when the printer receives a print job: Step 2 The ECU enables the laser/scanner assembly and the motor. re 43.

Back back to top How did we do? To reinstall the pad, see steps 6 through 8 of "Replacing the printer separation pad" on page 42. Join our community for more solutions or to ask questions. HP Error Code:16 - Toner Low Explanation:This normally means that your toner cartridge is either low on toner or empty.

See the user guide for more information. • Envelopes: Load envelopes with the narrow, stamp side forward and the side to be printed facing up. Hewlett-Packard Company 11311 Chinden Boulevard Boise, Idaho 83714 U.S.A. Note In several other HP LaserJet products, the ECU is also known as the controller PCA or the DC controller PCA. You will need the HP hardware product number for the product.

If you’re unsure how to fix your HP LaserJet 1300, then get in touch; we’ll get you printing again in no time.Our HP LaserJet 1300 repairs prices are fixed plus parts, Defective High Voltage power supply or on the LJ II/III the DC controller to High Voltage power supply can be defective.