However, the ability to send the entire document improves. If the local machine consistently gives this error code from different fax numbers, then the issue is probably hardware related and the machine should be replaced or serviced. Confirm that the fax/phone cable is no longer than required, and that it does not pass near unshielded electric motors such as fans, heaters, or household appliances. The remote user has oressed the Stop button. http://domcached.com/hp-fax/hp-fax-comm-error-345.html
Retry the fax reception when telephone line conditions have improved. Errors may still occur, and may result in degraded image quality on the received page. Can you help me? Try sending at a lower transmission speed. his comment is here
How To Disable Ecm On Hp Fax Machine
I changed the fax resolution from "fine" to "standard" using the button on the keyboard. I have checked my phone line with my telecoms provider for errors and there are none, and all the cables are connected in the correct manner. Set the host machine to receive at a slower transmission speed. If the local machine received several pages of a larger document successfully, ask the remote user to send the document in several smaller parts. 253 The remote machine attempted to initiate
Contact your DSL provider for the necessary filter.
HP only supports Analog.
The remote fax machine determined that there was a feature incompatibility between the two machines and terminated the session.
noisy/dirty telephone/fax line - corrosion on the terminal, joints, connectors, pins, plugs, jacks, telephone outlet or even on the provider's system.
This situation is usually due to extremely poor line conditions. The fax is digitized by my telephone company and then converted back to Analog when it goes out. Share on Facebook Share on Twitter Share on Google+ Share on Pinterest Share by Email × Question about HP OfficeJet 6210 All-In-One InkJet Printer Open Question When sending a fax, I Fax Error 346 Submitted: 4 years ago.
Hello and Welcome to FixYa!Sir/Ma'am these error are basically due the Communication error of Receiving/Remote Machines. Follow these steps to turn off the ECM setting: Press Setup. The call-waiting service can cause this error. If ECM is enabled, then disable it.
The faxed page is drawn into the feeder and emerges from the machine after which the touchscreen displays the message 'sending fax' for around 2-5 minutes (too long imho). Hp Fax Error 388 Errors might still occur, and might result in a degraded image quality on the received page. A simple solution would be to use a different outlet and/or use a surge suppressor. Press and select ECM.
Fax Error Codes
If the document is large, ask the remote user to re-send the document as two or more smaller documents. this content HP, get your @#$%[email protected]#$$^ together. How To Disable Ecm On Hp Fax Machine Retry the fax reception when telephone line conditions have improved. Hp Fax Error 344 However, the ability to receive the entire document will be improved.Error Code 420V.34 negotiations have failed from the originating product during phase four, which occurs after V.8 and before the first
Other reasons can include power brownouts and other power-related problems. The remote user must load a document to send before configuring the machine for polling. 321 322 323 324 There was a communication error with the receiving fax machine due to To receive faxes automatically, make sure the Auto Answer light is turned on. The click, heard for an incoming call, is actually a momentary disconnect of the line.Solution: Disable ECM. Hp Fax Error Code 350
Where can I find an interpretation of these error messages? Find Solutions, ask questions, and share advice with other HP product owners. Also under rare conditions, incompatibility between the two machines might cause the remote machine to abandon the call.Solution: Try sending at a lower transmission speed. have a peek here The noise problem might go away over time.
Some possible interruption/interference on transmission(s) are:1. Enable or disable the ECM setting. Do not use call waiting on a line with a fax machine. Check This Out An error code can have more than one definition (cause), and more than one solution.
Typically this is because the local fax machine answered a voice call. Retry the transmission. The user called the correct number, but the machine was configured not to answer. error number 351 The machine has a ECM (Error Correction)error.
These errors can occur if the phone lines in the area to be faxed are old or there is noise (static on the phone line).