Home > Hp Error > Hp Error Code 50.2

Hp Error Code 50.2

My next purchase will be a Xerox. Sometimes the reboot will allow the fuser to reset itself and you can print a few more pages. NOTE: On this model, it is very easy to change out the fuser. Turn the product power on. have a peek here

If the fuser has indeed been replaced with a known working fuser and still have the same error, then the next step to to check all the connections for the fuser Acción en curso... If you believe you purchased an HP supply, go to www.hp.com/go/anticounterfeit . Print failure, press OK.

The screen says to turn it off, then back on and if the issue persists, to call a tech. Recommended action Load the page in the indicated tray with the side to be printed face up, and the top of the page away from you and then press the OK Learn How to Post and More  Community News  Best of the Community Blog  Notebooks Notebook Operating System and Recovery  Notebook Boot and Lockup  Notebook Wireless and Networking  Notebook Audio  Notebook Video,

All print defects or cartridge failures incurred when an HP toner cartridge is used in Continue at Very Low mode will not be considered to be defects in materials or workmanship FIX Service 29.070 visualizaciones 12:08 hp laserjet P3015 - how to clean pickup roller - Duración: 3:04. Inicia sesión para que tengamos en cuenta tu opinión. Showing results for  Search instead for  Do you mean  or Post new question Post new question Question Reply Topic Options Subscribe Mark Topic as New Mark Topic as Read Float this

Provide feedback Please rate the information on this page to help us improve our content. Showing results for  Search instead for  Do you mean  or Post new question Post new question Question Reply Topic Options Subscribe Mark Topic as New Mark Topic as Read Float this Now put paper on tray 1 and turn on the printer and what happens. http://www.printertechs.com/printer-troubleshooting/378-50-2-fuser-error-on-hp-laserjet-2820-2840 My solution was for some reason the fuser temp got set to low so when the customer used labels in there machine it didnt fuse correctly.

Since it was only getting half the voltage it was supposed to be getting, it wasn't getting hot enough to fuse the toner, but it didn't trip the error either. Load Tray 1, / Cleaning mode, OK to start Description The product is ready to process the cleaning operation. erepairer 1.343 visualizaciones 3:04 HP LaserJet P1102W - How to replce fuser sleeve - Duración: 25:31. Turn the product power on.

Recommended action Turn the product power off, wait at least 30 seconds, and then turn the product power on and wait for it to initialize.

Recommended action Close the door. Well, I have tried turning it off and back on. Delete all print jobs from all computers connected to the printer.

by Stephen on Mar 2, 2007 at 6:36pm Add comment Please sign in to comment 0 hp laserjet 4200 110v fuser part number is RM1-0013 and 220v is RM1-0014 this problem navigate here As we all know, GA is part of the US and should be using 110V. Already have it ordered will let you know how it goes. Tried all ways of going around it but failed .

If my post resolves your issue please click the accepted as solution button under it.To thank a Tech for a post click the thumbs up button under the post.You can even Deshacer Cerrar Este vídeo no está disponible. Call us with any questions, toll free 866-352-7108 or local 608-831-2396 Purchasing information : HP Color LaserJet 2820 , 2840 fuser and maintenance kit Installation instructions: HP Color LaserJet 2820 , Check This Out Recommended action Turn the product power off, wait at least 30 seconds, and then turn the product power on and wait for it to initialize.

If the error persists, turn the power off and then on. Otherwise, I would have looked at your ip and seen you were in GA and told you to use a 110V fuser. Reply 0 0 SHThompson Distinguished Professor Posts: 2,718 Member Since: ‎05-09-2011 Message 3 of 3 (958 Views) Report Inappropriate Content Re: hp laserjet 4250n 50.2 fuser error Options Mark as New

Recommended action Press the OK button to continue printing the job, but output might be affected.

Cargando... Now the fuser 50.2 error isn't on and it is pulling the paper through, but it don't fuse the ink to the paper. Switch to another language: Catalan | Basque | Galician | View all Cerrar Sí, quiero conservarla. I noticed I do not hear the fuser spin up when the printer is turned on.So far I have replaced the fuser and formatter / main board.

Recommended action Wait for the cleaning process to finish. Turn off the product, wait at least 25 minutes, and then turn on the product. Turn the product power on. this contact form Iniciar sesión 6 0 ¿No te gusta este vídeo?

what is 50.2 Error Categoría Consejos y estilo Licencia Licencia de YouTube estándar Mostrar más Mostrar menos Cargando... Ecological Toner & Service 32.740 visualizaciones 7:17 HP Pro 400 M451dn Color Laser Printer Unboxing & Setup - Duración: 17:56. If the error is intermittent, attempt to isolate the issue to something specific in your environment. Reply 0 0 Ljubisa Tutor Posts: 11 Member Since: ‎10-29-2010 Message 3 of 4 (11,926 Views) Report Inappropriate Content Re: 50.2F.00 fuser error Options Mark as New Bookmark Subscribe Subscribe to

I didn't see anywhere that it wasn't fine for me to ask questions too. I even replaced the fuser. By using this site, you accept the Terms of Use and Rules of Participation Discussion Boards Open Menu Discussion Boards Open Menu Welcome to the Forum! I powered on the printer and the error message was gone.

keep up the good work by unknown on Mar 19, 2008 at 1:51am Add comment Please sign in to comment 0 In the USA we use 110 to 127 volts out BrokenPrinter1 108.810 visualizaciones 7:34 HP LaserJet Pro 400 M401dne (PT-BR) - Duración: 5:04. Recommended action To ensure optimal print quality, HP recommends replacing the toner cartridge at this point. Unexpected size in tray Load Press [OK] Description The product has detected paper in the tray that does not match the configuration for the tray.

Reply 0 Re: 50.2F.11 Fuser error 01-27-2016 06:56 AM I did call HP Support and the machine was under manufacturer warranty yet. Use paper that meets HP specifications. Discussion Boards Open Menu Discussion Boards Open Menu Welcome to the Forum! You can continue printing until you notice a decrease in print quality.