Home > Hp Error > Hp Error 55.a

Hp Error 55.a

Change wiring harness from the D.C. Verify that the SIMMS or memory cards are seated. It turns out that a fairly common problem is for the large white gear on the left side of the printer that drives the ink pump comes off the shaft. Replace the memory chip cable/connector or the DC controller.

When all three lights are on solid release the menu button and press the arrow back button and initialize disk should appear in the menu. I will have purchasing call in an order. Verify the environmental thermistor cable is securely connected. 3. For example, an old 'brown' duplex won't work with a brand new fusing unit. have a peek here

Also verify the configuration through the menus on the printer. Seeing that the printer will soon be due for a maint. General information with more detailed information available. Reseat the PostScript SIMM and/or replace it.

  1. If you want to use the duplex, then you will have to replace the fuser.
  2. Already a member?
  3. Again on the LJII/III we are starting to see more and more failures of the gear drive assembly.
  4. Just turn off the printer.
  5. When I plugged in the power cord the printer started and did about a 5 minute maintenance procedure and now works fine.
  6. Turn the device off and then on.3.
  7. Verify that there is no issue with the site power.
  8. In some instances, electrical noise in the cable can corrupt data during transmission to the printer.
  9. Replace the formatter board. 4.

Power cycle the printer. Check the feed and separation rollers in the printer and in the tray. ERROR 50.XXXX - ERROR 51 (Loss of beam detect) This is a beam detect error indicating a problem with the laser scanner. Many refurbished and re-manufactured fusers are available at retail; the color of the fuser rollers indicates if it is an HP fuser.

Error 22 Error/ I/O Config Error/ Par I/O Error/MIO Error 22 EIO X BUFFER OVERFLOW The EIO card in slot X has overflowed it's buffer and data loss will occur 22 Turn the printer off and then turn the printer on again.3. You could also have a defective or dirty exit sensor. On the 4P/5P printers, the top cover is open or no toner cartridge is installed.

by dmzcompute on Dec 30, 2008 at 6:39pm Add comment Please sign in to comment 0 The printer does not give any error messages but it does not detect the duplexer. Back back to top How did we do? Marek Williams Guest What is "55.A Printer Error" on a Laserjet 8000DN. Press Go to continue and the page with the error will reprint.

On the 5L, set the Enhanced I/O to AUTO (PCL mode) and resend the print job. The MIO card is defective or maybe just not seated correctly. by chris on Apr 10, 2003 at 1:57pm Add comment Please sign in to comment 0 Sorry to burst all of your bubbles - but even HP doesn't know what the On rare occasions a defective paper control assembly or actuator can cause this problem.

Thats why I gave the above information. If that works go back to the first application and try printing a different file to determine if the problem is file related. Anyone have any ideas on what I can do to fix this or any other tricks I can try? I kinda dont go for the incompatablity solution becuase most machines have these in there machines for quite some time before the error accures so why would it fail all the

ERROR 89 All Printers (except 5L/6L) The PostScript ROM's have bent or broken pins inspect the pins and reseat if necessary Check to see that the ROM SIMM's are in the Is the menu set for the size you're using? You probably don't believe me when I say there are also 2 different fusing-units (also, same HP code). Defective toner cartridge in the Laserjet 4 Plus only.

So far it's been great; we love the 11"x17" and duplexing capabilities. Also check for any partially peeled labels, this can be a disaster if they come off inside the printer. ERROR 14 No EP Cartridge or No Toner Cartridge No toner cartridge or cartridge not fully seated - pull it out and install it again.

The media that is loaded does not match the settings of the paper tray.

HP LASER PRINTER 4345MFP, 5025MFP, 5035MFP ERROR 55.XX 1.The print engine is not communicating with the formatter. Pl. Check the connector inside the machine. HP LASER PRINTER 9000, 9040, 9050MFP 1.

The code 55.A occurs if there's a duplex-unit installed and you just replaced the fuser. Also an attempt to press the GO button mght make the printer resume the job it was handling. Back back to top How did we do? Back back to top How did we do?

If you cycled the power, it would work for a little while, but eventually come up with the error again. Recalibrate the D.C controller board and the formatter board.3. HP LASER PRINTER 5000, 5100 1. Check the cable to the ECU. 3.

All The Best: Pineworks Posted on Feb 13, 2010 Helpful 0 Not Helpful Flag You can't post conmments that contain an email address. × Comment Anonymously Video Images Add Your Answer flipfloppity posted Aug 14, 2016 Upgrade mobo but keep cpu and... I swapped a known working/detected duplexer and it was not detected.