Home > Hp Error > Hp Error 50.2

Hp Error 50.2

You can continue printing until you notice a decrease in print quality. So always check your fuser temp settings before replacing fusers for imporper fusing. Recommended action Install the toner cartridge. If no, then you got a defective fuser and you need to return it for replacement.

Loading... by unknown on Jun 10, 2011 at 1:29pm Add comment Please sign in to comment 0 maybe this one will help about the fuser error 50.2i think the problem is in Does it need the 220V fuser even though it says 110V but language is in french? - Anonymous 0 Pull the fuser out. If that is the case HP did not have any solution and had us send the printer back. http://www.printertechs.com/printer-troubleshooting/11-50-2-fuser-error

by mharris on Jan 18, 2006 at 3:33pm Add comment Please sign in to comment 0 That is indeed a fuser error. You can get reconditioned fusers from partsnow.com or depot-america.com on advance exchange. Plug the product directly into the wall socket.

  • A customer configurable option on this product is "Prompt to Remind Me in 100 pages, 200 pages, 300 pages, 400 pages, or never." This option is provided as a customer convenience
  • I am receiving this error: '50.2F.11 Fuser error".
  • Critical error messages can indicate some kind of failure.
  • Recommended action Press the OK button to clear the message or load the correct paper into Tray 1.
  • I did see on some blogs, people were talking about possible power issue/voltage issue.

Recommended action Turn the product power off, wait at least 30 seconds, and then turn the product power on and wait for it to initialize. Well, I have tried turning it off and back on. Sign in to add this to Watch Later Add to Loading playlists... In rare cases, a specific IP address has been seen to cause the error; assign a different IP address to the printer.

Reply 0 0 coloradofinn Top Student Posts: 2 Member Since: ‎01-19-2016 Message 3 of 3 (1,542 Views) Report Inappropriate Content Re: 50.2F.11 Fuser error Options Mark as New Bookmark Subscribe Subscribe The 4200 fuser only works in a 4200 not like the 4250 which also works in the 4350. Most fuser models can be installed by an end user, without needing a service technician.  We have installation instructions under the Tech Support section of our Web site.  Call us with

Or press the OK button to use the paper currently in the tray.

The screen says to turn it off, then back on and if the issue persists, to call a tech. Incompatible black Description You have installed a toner cartridge that is intended for use in a different HP product model. and an instructional cd. I noticed I do not hear the fuser spin up when the printer is turned on.So far I have replaced the fuser and formatter / main board.

About Press Copyright Creators Advertise Developers +YouTube Terms Privacy Policy & Safety Send feedback Try something new! Manual feed , Press OK to use available media Description The product is set for manual feed mode. That was after registration, dc controller and ps replacement. by Stephen on Mar 2, 2007 at 6:36pm Add comment Please sign in to comment 0 hp laserjet 4200 110v fuser part number is RM1-0013 and 220v is RM1-0014 this problem

Alert and warning messages appear temporarily and might require you to acknowledge the message by pressing the OK button to resume or by pressing the Cancel button to cancel the job. Learn How to Post and More  Community News  Best of the Community Blog  Notebooks Notebook Operating System and Recovery  Notebook Boot and Lockup  Notebook Wireless and Networking  Notebook Audio  Notebook Video, Unit has been sitting un-plugged. Close Yeah, keep it Undo Close This video is unavailable.

I noticed when powering on the machine the fan didn't come on. Since it was only getting half the voltage it was supposed to be getting, it wasn't getting hot enough to fuse the toner, but it didn't trip the error either. Now put paper on tray 1 and turn on the printer and what happens. Thank you!

what is 50.2 Error Category Howto & Style License Standard YouTube License Show more Show less Loading... by dmzcompute on Dec 6, 2006 at 4:27pm Add comment Please sign in to comment 0 Wondering if you got this one figured out?I too have a 4200 showing the 50.2 Genuine HP supply installed Description A genuine HP toner cartridge was installed.

I have found the problem, I just need to get the 110v instead of the 220v.

You need to replace the fuser. Printer Repair Parts, Support and Supplies Printer, copier, and fax repairs done right the first time.About MyselfContact UsBrotherHPLexmarkXeroxHome » HP Support Articles » How to Deal with the 50.2 Fuser Error Plug the product directly into the wall socket. First Time Here?

Black cartridge low Description The toner cartridge is nearing the end of its useful life. By using this site, you accept the Terms of Use and Rules of Participation Discussion Boards Open Menu Discussion Boards Open Menu Welcome to the Forum! Recommended action Turn the product power off, wait at least 30 seconds, and then turn the product power on and wait for it to initialize. Once an HP toner cartridge has reached very low, HP's Premium Protection Warranty on that toner cartridge has ended.

Show more Language: English Content location: United States Restricted Mode: Off History Help Loading... If my post resolves your issue please click the accepted as solution button under it.To thank a Tech for a post click the thumbs up button under the post.You can even Learn How to Post and More  Community News  Best of the Community Blog  Notebooks Notebook Operating System and Recovery  Notebook Boot and Lockup  Notebook Wireless and Networking  Notebook Audio  Notebook Video, I replace it and the message was gone.

Recommended action Select the correct print driver. The same error was thrown. As we all know, GA is part of the US and should be using 110V. Tags Fun 1,317 views 5:15 HP Color LaserJet Pro M252dw Unboxing & Setup - Duration: 19:53.

Turn the product power on. I'm new to the forum, and hoping you can help.My trusty HP Laserjet 5000n is posting an error message "50.2 Fuser Error." HP wants $900 to fix it, which sounds excessive. by darrell fuller on Apr 25, 2007 at 8:37am Add comment Please sign in to comment 0 I don't know why it would work when you open and close the cover, It's cheaper to replace just that than a whole fuser.

Misprint, Press OK Description Paper has been delayed as it moves through the product. After around off playing with it, it still wouldn't print right, and the error 50.2 come back on, so it will print (if that's what you want to call it) with Load Tray 1, / Cleaning mode, OK to start Description The product is ready to process the cleaning operation.