The serial transmission error has occurred. 2. Occasionally the contact for the micro switch will get bent and will have to be replaced. You can remedy this by replacing the paper guide plate assembly, RG5-2248-030. A connection with the EIO card in slot X has been abnormally interrupted.3.
Server Infrastructure: Supermarket Chain New Server Infrastructure Project and Deployment built for a Supermarket Chain Wireless Project Install and configure Cisco WISM's and Aironet equipment TECHNOLOGY IN THIS DISCUSSION Join On the II and III Series printers, this error message can be caused by a faulty paper control PCA. II, III Replace cable from DC Controller PCB to HV power supply. ERROR 43 / ERROR 43 OPT INTERFACE This indicates a communication problem between the formatter PCA and an optional interface installed (such as a network card).
40 Eio Bad Transmission Error
Caution needs to be used when installing the new assembly - be careful of the sensor flag spring! 5Si - Can be caused by field replaceable units (FRU's) not installed correctly. address in your browser and see if it pings.6. Replace PS1 if defective.
Error 55 On IIISi/4Si Printers this is due to the DC controller not receiving the proper information upon startup.
Replace this as an assembly.
Check the fan connector and make sure that the fan is not blocked. 2.
LJ 4250/4300/4350 A printer fan is not funtioning.
Back back to top How did we do?
Error 21 Print Overrun The print job is to complex.
Mark as duplicate Convert to a question Link a related branch Link to CVE You are not directly subscribed to this bug's notifications.
Bad paper exit sensor.
I did not try a new formatter yet as there are so many with this problem. Changing drivers to HP Laserjet 8150 Foomatic/ljet4 solved the problem. IIISi/4Si check the door open sensor flag, PS1. Remove and reseat the optional interface card.
Run self test and look under Installed Options: Disk Bad hard disk PC Install 4V No paper tray installed in lower cassette Improperly seated paper cassette. Eio Card Tractor feed paper with the edges ripped off doesn't seem to work very well. Look for bits of paper lodged in the path particularly around the sensors. 4L/4P printers can have paper stuck in the pickup area which is accessed by removing the screw over anchor Error 10.32.00 Unauthorized Supply Alternates with for help press "?" - A new non-HP supply has been installed this message continues until you press the check button or install an HP
Improperly seated SIMMs or font cartridge - remove, check/clean contacts re-install and try again. Back back to top How did we do? Back back to top How did we do? A broken tooth on one gear is all it takes.
Power printer OFF!!) IIP, IIP+, IIIP See service note 33471-011 if SN is between 0000J00000 and 2949J22222 Replace fuser assembly Replace power supply IIISi, 4Si Make sure fuser is correctly seated Ethernet and TCP divide data into packets partly so that they can discard errors. However this time they are the bottom rather than top of the list. Reply 0 0 ldavis1224 Student Posts: 1 Member Since: 11-15-2013 Message 8 of 13 (84,137 Views) Report Inappropriate Content Re: LaserJet M602 - 49.4a.04 Error Options Mark as New Bookmark Subscribe
Turn the image adapt and page protect to ON or AUTO either from the control panel or from within HP Explorers Remote Control Panel. 5P/5Si Same as above, Press GO to Press Select button to resume printing, some data loss will occur, you will need to add memory or reduce the complexity of the print job. Turn the printer off, and then turn the printer on. Depending on the model, a firmware DIMM may need replacing or a flash update.
Check for opens on the cable.
The client insists his network connection is okay. Veronica Casto Houston, TX It is nice to place anonline order & get to talk to an actual person. ERROR 41-X X= 1,2,4,5 A temporary error occured - Press "CONTINUE" to clear. 41.3 Error - Unexpected paper size - more than one sheet of paper picked up. This page is presented as a public service.
Please DO NOT Email for assistance in troubleshooting problems. X represents the error location and can equal one of the following: 1 = Slot number 1 2 = Slot number 2 3 = Slot number 3 6 = Card in Ruben Verweij (ruben-verweij) wrote on 2008-05-14: #2 error_log Edit (14.2 KiB, text/plain) No, I don't need to press START, even though the printer asks for it... Affecting: system-config-printer (Ubuntu) Filed here by: Pascal De Vuyst When: 2010-10-02 Completed: 2013-03-12 Target Distribution Baltix BOSS Juju Charms Collection Elbuntu Guadalinex Guadalinex Edu Kiwi Linux nUbuntu PLD Linux Tilix tuXlab
Changed in hplip (Ubuntu): status: Confirmed → Invalid Changed in system-config-printer (Ubuntu): status: New → Invalid See full activity log To post a comment you must log in. A serial data error (parity framing, or line over run) has occurred during the reception of data. 2. Error 24 Job Memory Full The print job is too complex to be processed. i have tried the above approaches and they dont seem to work?
See the catalogue. then choose under network printer "AppSocket/HP JetDirect" in the Host field enter the ip address of the printer click forward, select various options and print a test page. Some protocols are highly tolerant to an error and will recover from a problem even if they can only do so hours later. It can also be caused by a defective DC controller.
The media that is loaded does not match the settings of the paper tray. LJ4 Bad output rollers (See service note C2001-03) 500 sheet lower cassette not properly adjusted. (See service note C2001-01) LJ4, 4+ Rear door open. This kit contains a new fuser assembly, the various rollers for the paper feed path and instructions for installing the lit as well as the instructions for resetting the page count Press SHIFT+CONTINUE to clear.
The page containing the error will automatically be reprinted if jam recovery is enabled. (Or, you might want to press CANCEL JOB to clear the job from the printer’s memory.) For Press the spring contacts and listen for the micro switches. Turn the printer off and delete the print queue. Very frustrating. Almost all of our JD cards are the 600N model, though we do have some generic JD cards out there.
Remember to reconnect all cables that connect the printer to the network or computer. 9. The printer required a firmware update. This is the board mounted to the DC power supply which is in the right front corner of the printer.