Solution one: Make sure that the All-in-One is plugged in Follow these steps to make sure that the power cord is connected to the rear of the printer and plugged into Press and hold the Start Copy Black button () and the Start Copy Color button () until the printer makes some noise. In this article I will tell you how to solve the HP Deskjet 610c Printer printer not activated error code 30 problem. If any torn pieces of paper remain inside the product, more paper jams are likely to occur. http://domcached.com/hp-deskjet/hp-deskjet-935.html
If the test page does not print, continue with the next solution. Patri, Sep 16, 2004 #1 Advertisements Show Ignored Content Want to reply to this thread or ask your own question? If the test page does not print, continue with the next solution. Lift the scanner lid.
Figure 60: Close the cleanout door NOTE: Make sure that tabs are locked in place to avoid future paper jams. Press the Power button to turn off the printer. Issue: The Power light blinks In this condition, the following control panel light pattern displays: Power light: Blinking Attention light: Off Color ink level icon: Displays normal ink level Black ink The test page prints.
Solution: Load paper Follow these steps to load paper and continue your print job. Open the HP printer software: Windows 8 On the Start screen, click or tap the printer's tile. Disconnect the USB cable from the rear of the product if it is not already disconnected. Reattach the cleanout door.
Solution four: Clean the rollers Dust, paper fiber, and other debris might accumulate on the paper feed rollers and cause paper jams and paper feed issues. Windows XP Click Start (), click All Programs, click HP, click the folder for your HP printer, and then click the icon for your HP printer (). Welcome to the Printer Forums where you can ask questions or find solutions to printing problems. http://www.printerforums.net/threads/hp-deskjet-610c-error-in-printing.9155/ Press and hold the Start Copy Black button () and the Start Copy Color button () until the printer makes some noise.
If you press and hold the Power button too long, the printer might turn on and then turn off without restarting. The carriage moves to the center of the printer. by wefix365hp on Oct 3, 2016 at 11:41pm Add comment Please sign in to comment Please sign in to comment HP DeskJet 610C Buy discount ink Buy this printer More HP Disconnect the power cord from the rear of the product if it is not already disconnected.
Solution two: Make sure that the electrical outlet works Unplug the power cord from the electrical outlet. CAUTION: If the paper tears when you remove it from the rollers, check the rollers and wheels for torn pieces of paper that might remain inside the product. Remove any loose sheets of paper from the input tray. If these steps resolved the issue, and the test page prints, there is no need to continue troubleshooting.
Press the Power button to turn on the printer. Check This Out Figure 66: Holding input tray guard Look down through the open input tray and find the gray paper pick rollers. If the test page does not print, continue with the next solution. Step 2: Print a test page Printing a test page verifies if the hardware functions correctly.
OS X v10.9, v10.8, and v10.7 Click Macintosh HD, click Applications, and then double-click Hewlett-Packard.
Reconnect the power cord to the rear of the printer.
Visit HP SureSupply to check ink or toner cartridge compatibility, or purchase replacement cartridges.
Make sure that the icon on the cartridge matches the icon on the slot.
I have met such problem days before and before that my HP Deskjet 610c Printer worked well.
Firmly push the carriage to the left side of the product, and then to the right side. If the issue persists, continue to the next solution. If you experienced a recent power surge, you might need to reset the power module. Source The test page prints.
Figure 67: Paper pick rollers Dampen a long cotton swab with bottled or distilled water, and then squeeze any excess water from the cloth. Follow the on-screen instructions to order new cartridges or check cartridge compatibility with your printer. With the product turned on, disconnect the power cord from the rear of the product.
If the carriage is stuck in the middle of the product, move the carriage to the right side of the product.
Check the printer to make sure that it is on. In the event that the roller is excessively old or exhausted, it should be supplanted or you can attempt some elastic roller restorer/rejuvenator that can help old rollers.If you want to Step 1: Reset the All-in-One Follow these steps to reset the printer. The printer lights might flash and the carriage might move.
If the carriage is stuck on the right side of the product, move the carriage to the left side of the product. The carriage moves to the center of the product. Figure 49: Lower the output tray Pull out the tray extender. have a peek here Do not hold the button down.