The diagnostic page might look different than the sample below, but right and left cartridges always print on the same areas of the page. The chip may be missing or defective or contain incorrect information. There are also other things that can cause this problem, such as anti virus software. Step one: Remove the cartridges Press the Power button () to turn on the product. http://domcached.com/hp-deskjet/hp-deskjet-5100-error.html
Figure 17: Reattach the duplexer Option two: Clear the jam from the rear access door Follow these steps to remove jammed paper from the rear of the product. If the issue persists, continue with the next solution. Reach inside the product through the paper output tray, and then manually move the carriage. Back back to top Error 16 Toner Low Toner cartridge is empty or toner in cartridge is not distributed evenly.
Hp Deskjet 5650 Manual
Follow these steps to clean the paper rollers. Step two: Print a self-test report Print a self-test report to make sure that the hardware functions correctly. Step two: Identify cartridges on the diagnostic page Use the sample diagnostic page below to identify the problem cartridge. How to print a self-test report Load plain paper in the paper tray.
XX03 Replace Printhead smartchip failure Replace printhead XX04 Replace XX05 Replace You have installed a new tubes system and the printer is priming them.
Windows Vista Click the Windows icon (), and then click Devices.
Press the Resume button () four times.
We have not detected any issues with your product. You may find a relevant support option by selecting any of the helpful topic tabs on this page or by entering your
This error can also be caused by a defective interlock switch assembly.
If the board becomes defective, you will receive an error 12.
The self-test report prints.
Can also indicate a mis feed or paper not being picked up.
Error 79 Software/drivers, Memory PCA's, Font-Macro-Personality Cartridges, option I/O Cards. Replace the Fan. Solution two: Make sure that the cartridges are properly inserted Follow these steps to remove and then reinsert the cartridges. Hp Deskjet 5650 Won't Print Verify SIMM's are seated properly, replace any defective 5Si 59.X Main motor malfunciton X=1: Main motor startup failure, X=2: Main motor rotation 59.XY 4200/4300 Series Main motor failure, check wiring harness
Verify that the SIMMS or memory cards are seated. Hp Deskjet 5650 Troubleshooting Press the Power button () to turn on the product. Touching these parts can result in clogs, ink failure, and bad electrical connections. http://support.hp.com/us-en/document/c00022701 Printing with an empty ink supply may seriously damage your printhead, ink tubes, and printer.
Very helpful Somewhat helpful Not helpful End of contentUnited StatesHP WorldwideStart of Country / Region Selector contentSelect Your Country/Region and LanguageClick or use the tab key to select your countryArgentinaAustraliaBelgiqueBoliviaBrasilCanadaCanada-françaisČeská republikaChileColombiaDeutschlandEcuadorEspañaFranceIndiaIrelandItaliaMagyarországMéxicoNew Hp Deskjet 5650 Clean Print Heads Also verify the configuration through the menus on the printer. Disconnect the power cord from the rear of the product. X = Description 4 Printer Fan 7 Duplex Fan 1.
Hp Deskjet 5650 Troubleshooting
You could also have a defective or dirty exit sensor. http://h20564.www2.hp.com/portal/site/hpsc/public/psi/troubleshootResults?sp4ts.oid=74341 Right-click the icon for your HP product, and then click Printer Preferences. Hp Deskjet 5650 Manual Laser printers are page printers and require the entire page to be processed before beginning to print. Hp Deskjet 5650 Installation Figure 41: Raise the cartridge latches Slide the cartridge out of its slot, and then pull it towards you to remove it.
For example, 1 = fan motor 1. Check This Out One or both cartridges might be improperly inserted. Close the top cover. NOTE: If you are using photo cartridges, two cartridges must be inserted. Hp Deskjet 5650 Ink Light Flashing
Also caused by the density adjusting PCA located behind the density adjusting slide switch. ERROR 49.XXXX A critical firmware error has occurred that caused the processor on the formatter to abort the operation. Use both hands to pull any whole sheets of paper to avoid tearing them. Source Solution two: Plug the power cord directly into a wall outlet Press the Power button () to turn off the product.
This can generally get you 100 or so more pages. Deskjet 5650 Test Page The printhead is still able to produce good image quality. XX04 Replace The smart chip inside the ink cartridge contains incorrect information.
Defective toner cartridge in the Laserjet 4 Plus only.
XX09 Replace There is an electrical failure. Make sure that it snaps into place. I will have purchasing call in an order. have a peek here Figure 59: Do not touch the contacts or the ink nozzles Close the top cover.
Step one: Reset the printer Press the Power button () to turn on the product. Make sure that the carriage can move freely across the width of the product by gently pushing the carriage to the left and then to the right. NOTE: Do not select Automatic. If any torn pieces of paper remain inside the product, more jams are likely to occur.
Press the Power button () to turn off the product. In the example shown above, one or more of the printheads have a replace message displayed. XX21 Replace The printhead has reached a degradation level that prevents the printer producing acceptable image quality consistently. XX06 Replace The printer detects an incorrect printhead cleaner.
Also check the toner level sensor and the toner cartridge itself for damage. Wait at least 15 seconds. Look for the conductive contacts on the cartridge and the corresponding contacts in the printer and make sure they are clean and free of contaminants. If you can not find the Uninstall a Program than you should just remove it.
Issue: The Resume light and the Print Cartridge light are blinking In this error condition, the following light pattern displays on the control panel: Print Cartridge status light: Blinking Resume light: With the product turned on, disconnect the power cord from the rear of the product. Solution five: Service the printer If you have completed all the solutions listed above and are still experiencing a problem, continue to the Service the printer section at the end of We stock the full range of HP printer service parts needed for preventive maintenance and repair service.
Solution four: Plug the printer directly into a wall outlet Follow these steps to plug the product directly into a wall outlet to make sure that the power source functions correctly.