Home > Hp Color > HP Color Laserjet 4600 Error Codes

HP Color Laserjet 4600 Error Codes

Contents

Before I got your reply I had to go to the customer.. If you can put the old one back in and see if it at least prints but just jams. If the printer works without the card then that is your issue. Watch the control panel. Source

You will probably have to replace the dc controller. I already tested every driver I found online (PCL5, PCL6). top 13.05.00 JAM IN PAPER PATH X For help press ? I've replaced dozens of them on 4600s. http://h20564.www2.hp.com/portal/site/hpsc/public/psi/troubleshootResults?sp4ts.oid=74301

Hp 4600 Laser Scanner Assembly

Watch the control panel. Find by product name or number (e.g. To ensure the tests are valid, turn the printer off and on between steps to determine if the error message has been cleared. Continue holding the green check button until the Ready, Data, and Attention lights flash once, and then stay on steady.

  • PrintCopy .infoservice Service manual Parts List Error Code Equivalency Sign In Contacts About Us
Service manual Error Code Parts List Equivalency Complete information for maintenance and repair printers, copiers, fax-machines
  • If the error persists, reinitialize the hard disk or flash DIMM.
  • Thanks guys...Sam by Anonymous on Dec 19, 2007 at 7:29am Add comment Please sign in to comment 0 HP 4600 5 1/2 years old; 1500 copiesSucking ink like crazy.
  • Watch the control panel.
  • Your best bet here is to request an "alienation kit" from HP and if you have any mechanical skills, changes these parts out.
  • I suspect that it is not warming up but shouldn't it throw a code if it doesn't? If the error persists, contact HP Customer Care Support. Reseat the EIO card and turn on the printer. Hp 4600 Paper Pickup Assembly by unknown on Jan 5, 2005 at 2:08pm Add comment Please sign in to comment 1 Okay LizHere we are getting into the very complex ( and sometimes amuzing) world of

    Action Turn the printer off, and turn it on again. Laser Scanner Assembly For Hp Color Laserjet 4600 Series by unknown on Mar 11, 2008 at 10:49am Add comment Please sign in to comment 1 I have a HP460 that has registration problems. If the error persists, contact HP Customer Care Support. http://www.printertechs.com/printer-troubleshooting/346-51-2c-51-m-51-2y-51-2k-error-on-hp-color-laserjet-4600 by Anonymous on Jan 10, 2009 at 8:24am Add comment Please sign in to comment 0 Mulitpaging on this printer is never caused by the pickup rollers, in fact multipaging is

    These color lasers will not display calibrations errors on the control panel but they will be in the event log.Let us know what the printer number is.I will get back to 51.2c Printer Error Press (Down Arrow) button once. If the error returns try a different EIO slot. top 13.0A.00 JAM IN TOP COVER AREA Description Shipping blocks are still in the fuser.

    Laser Scanner Assembly For Hp Color Laserjet 4600 Series

    The printer will perform a cold reset and then continue its power-on sequence. i replaced the black toner cartridge. Hp 4600 Laser Scanner Assembly top 68.0 PERMANENT STORAGE FULL FOR HELP PRESS ? 68.0 Permanent Storage Write Fail Hp Printer Perform a cold reset on the printer.

    Press (Down Arrow) to highlight PRINT QUALITY . this contact form top 10.30.01 SUPPLIES ERROR For help press ? The magenta and yellow were leaving toner on the sides of the transfer kit, but the black is actually spitting toner at the top and bottom of the page. Watch the control panel. Hp Color Laserjet 4600 Service Manual

    top 54.1 PRINTER ERROR Description A low fuser temperature error has occurred. This test print is totally generated internally. Enter that and you'll find the reset options for both the transfer kit and the fuser kit. have a peek here Continue holding the (Select) button until the Ready, Data, and Attention lights flash once, and then stay on steady.

    Turn the printer off, and turn it on again. Hp 4650 Cold Reset by dmzcompute on Jan 10, 2009 at 11:29am Add comment Please sign in to comment 0 Hi Tony C.!Thanks for your answer. i have changed the color registration detection assembly and also the dc controller pca.

    When the memory starts counting, press and hold the green (Select) button.

    Action Ensure the print cartridge is a Genuine HP cartridge. If it fixes it, we will post another message. If unexpected behavior occurs, turn the printer off and then turn it back on again. 68.2 Permanent Storage Write Fail This is a fairly recent occurrence so we are still dumbfounded, as our printer engineers have only encountered the problem at other sites, when the printer was using NON Hp toners,

    Press (Select) to select PRINT QUALITY . If using pcl5 driver, try pcl6 or ps or just try a driver they are not using. The printer will perform a cold reset and then continue its power-on sequence. http://domcached.com/hp-color/hp-color-laserjet-3600-error-54-18.html alternates with TO CONTINUE PRESS Description One or more settings saved in the onboard NVRAM or removable disk (flash or hard) have been reset to the factory defaults.

    top 54.14 PRINTER ERROR Description There is a problem with the yellow density sensor. When the memory starts counting, press and hold the green (Select) button. Release the (Select) button when the Ready, Data, and Attention light are on steady. Press (Up Arrow).

    The linear assembly had some teeth missing. Replace the cyan cartridge If this message persists, contact an HP-authorized service or support provider. Press (Select). Continue holding the green check button until the Ready, Data, and Attention lights flash once, and then stay on steady.

    Use Web Jetadmin software to delete files from the storage device. by Stephen on Oct 18, 2006 at 4:56pm Add comment Please sign in to comment 0 It doesn't say an error or nothing, it's like it thinks the printer itself is