Order supplies alternates with Ready More than one supply item is low. Comment Flag More Print this page Share this page You can't post conmments that contain an email address. × Comment Anonymously Video Images 4 Suggested Answers POCBM 121 Answers SOURCE: my Second is the fuser motor test.1. Invalid driver Press OK The driver is not correct for this printer. http://domcached.com/hp-color/hp-color-laserjet-3600-error-59-90.html
Insert or close tray X A tray is open and the printer is trying to print from another tray. To print the event log, open the secondary service menu, select Service Reports, and then select Error Report. Unauthorized alternates with To accept press OK A new, non-HP supply has been installed. Replace the DC controller PCA.
Select the component test options when prompted by the printer.Menus cannot be opened during component tests, so serves the same function as the Stop button.â— Fuser motor. If you follow the service manual instructions a lot more of the machine has to be disassembled so if you have to do this I would use the service manual with Replace the ETB.
Close the front door.
Replace the DC controller PCA. 50.7 Error: Verify the fuser is installed correctly and fully seated.
Service or repairs that are required as a result of using non-HP supplies are not covered under HP warranty.
Unauthorized supply in use alternates with Ready The printer has detected that a non-HP supply is currently installed and OK was pressed to override.
Solution: 1. Replace the print cartridge. If the error persists, contact HP Support. An error occurred with the magenta print-cartridge drive motor during startup or rotation.
If the message persists, make sure the following connectors are seated correctly: On the driver PCA, connectors J201, J202, and J203. Check that connector J5008 on the fuser motor and J213 on the driver PCA are seated correctly. If the resistance is not 100 kohms to 3 Mohms, replace the fuser. read the full info here Reseat the firmware DIMM.
Replace the DC controller PCA if necessary. 49 Error Turn off then on A critical firmware error has occurred. Open the front door and clear the jam. Remove the fuser. Replace if needed.
Fix your printer ! Clicking Here An error occurred with the cyan print-cartridge drive motor during startup or rotation. Judy Klautt I have a same problem, Did you find a solution? Replace the black print-cartridge drive motor.
A problem with the Yellow Print cart. Check This Out Learn more. Load tray # alternates with Press OK for available media Tray X is either empty or configured for a type and size other than that specified in the job. Check that connector J6007 on the fuser is seated correctly.
Remove the print cartridges, and then reinstall them. Non-HP installed alternates with To accept press OK A new, non-HP supply has been installed. An error occurred with yellow print-cartridge drive motor during startup or rotation.
Replace the DC controller.
Ensure that all trays are configured correctly before printing again. Replace the fuser drive assembly. sin mas por el momento... Install a supported DIMM.
Sign-in Register Site help Skip to ContentSkip to FooterLaptops & tablets Business Premium Gaming Standard laptops Workstations Convertibles & detachables Tablets 3-in-1 Desktops Business Immersive Gaming Towers Workstations All-in-ones 3-in-1 Printers Or just drag it here! This is a warning message only. have a peek here Replace the memory controller PCA if necessary.
Nov 19, 2010 | HP LaserJet 3600n Printer 1 Answer What is causing my HP 3600n to have the error code 51.23? Loading...Oops :Please try again. If there is no conduction in the subthermistor, measure the resistance between fuser connectors J6007LA-2 and J6007LA-3. Open the tray and clear the jam.
It could be a paper jam, motor failure (not likely but possible), the board that drives the motor, even a fuser with totally worn out bearings. Initializing . . . An error occurred with the fuser motor during startup or rotation. Parts are thoroughly tested, inspected for damage & defects and guaranteed 100% fully functional. $25.00 HP RM1-2763-000CN Fuser Assembly MFG Part Number: RM1-2763-000CN Condition:Refurbished MFG:HP This HP RM1-2763-000CN
If the message persists, reconnect the following connectors: Relay PCA: J7006 and J7001 DC controller: J1014 Replace the top-of-page sensor. Replace the driver PCA. 59.53 Error 59.63 Error An error occurred with the yellow print-cartridge drive motor during startup or rotation. Open the front door and top cover and clear the jam. Replace the driver PCA. 59.51 Error 59.61 Error An error occurred with the cyan print-cartridge drive motor during startup or rotation.