This is a common error when attempting to fax over VoIP, such as MagicJack. Contact the sender to make sure a document is ready and correctly loaded in the sending fax machine. Errors might still occur, and might result in a degraded image quality on the received page. Source(s): http://h20000.www2.hp.com/bizsupport/Tec... Source
If the machine is in V.17 mode, it is likely the connection has been interrupted. It looks like the 388 error message means to much noise on the line.Fax Error Codes View solution in context Reply 0 0 garytech1 Regents Professor Posts: 4,641 Member Since: 01-11-2012 Enable the BFT capability on the remote machine if supported. Disable ECM, and then try to receive the fax again. news
Hp Fax Error 344
You should try again at a different time. Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content 05-22-2012 09:25 PM hp officejet 4500 wireless fax. Also pulled the phone off the line, so there's no other device. View Solution.
Interpreting fax send error codes This table contains fax send error codes. More questions HP Fax/Printer 6300 with error code 388? This is usually caused by one of the following reasons: The user called the wrong number. How To Turn Off Ecm On Hp Fax Machine I have a HP 8500a Plus all in one machine.
It is possible that the remote user inadvertently attempted to poll. Fax Error 350 The remote machine disconnected immediately before sending any further fax tones or T.30 frames. Disable ECM. The call-waiting service can cause this error.
Call the telephone provider if line conditions fail to improve. For example, the local machine wanted to initiate polling, but the remote machine did not support this mode of operation. This error can occur if the other fax machine is using a fax format incompatible with the HP fax product (usually during color faxing). 430 The sending fax is unable to Find Solutions, ask questions, and share advice with other HP product owners. Fax Error 388 Hp Officejet
The click, heard for an incoming call, is actually a momentary disconnect of the line.
Try to receive the fax when telephone line conditions have improved.
The remote user pressed the Stop key while the reception was in progress.
Retry the fax reception when telephone line conditions have improved.
Wait several minutes between the end of one transmission and the start of the next transmission. 383 ECM Disable ECM, and then try faxing again.
Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content 11-19-2011 12:55 AM How do you change the fax speed?
An error code can have more than one definition (cause), and more than one solution.
Learn How to Post and More  Community News  Best of the Community Blog  Notebooks Notebook Operating System and Recovery  Notebook Boot and Lockup  Notebook Wireless and Networking  Notebook Audio  Notebook Video,
If you are still getting an error 388, this means that the noise is further down the phone line rather than coming from your home or office.
If not, reconfigure the local machine for a normal fax transmission.
Error correction off, baud rate either slow or medium. Disable V.34 on the local machine and attempt the transmission using the V.17 mode. ( See error 227 for changing to a slower speed or disabling V.34 .) http://h20000.www2.hp.com/bizsupport/Tec... Ask the community! Hp Fax Error 358 Insert a new phone cord if you're using an old cord for your Officejet 7130.
Poll transmission from a remote machine is typically configured with each fax session. Brother MFC 240C... How do I get a print? 5 answers More questions How to let my printer hp deskjet 3630 recognise its original cartridge which i refilled by ink? 5 answers I do Move to the next step if you still can't send a fax.
If the local machine received several pages of a larger document successfully, ask the remote user to send the document in several smaller parts. 253 The remote machine attempted to initiate On many fax machines, it is possible to accidentally initiate a fax reception in the following cases: There is no paper in the machine. The remote machine temporarily disabled answering due to a condition such as lack of paper or a paper jam. Move to the next step if you still can't send a fax.
Thedocumentcan be foundhere. Fax quality might be degraded. It looks like the 388 error message means to much noise on the line.Fax Error Codes Reply 0 0 Everyone's Tags: AS1 View All (1) sgcromer Honor Student Posts: 2 Member Enable the remote diagnostics capability on the local machine, if available.
You can only upload photos smaller than 5 MB. Click here to find out: Model Number.I will provide a HP document on Interpreting Error Codes in Fax Communication.If you have preformed all the troubleshooting steps from this document, then please This error does not result in the session being terminated immediately. Call the telephone provider if line conditions fail to improve 384 The local machine attempted a black JPEG transmission to a machine that does not support this mode.
Reconfigure the local fax machine to use different configuration settings, enable or disable the ECM setting. 223 ECM 224 The local machine was unable to receive an entire page even after The user at the remote machine might have pressed the Stop key.