Home > Error Code > Hyosung Atm Error Code 3-d1500(00)

Hyosung Atm Error Code 3-d1500(00)

Contents

Use a business card or stiff paper to clear jams. Check a jammed note in 3 Cassette or remount it 4. If they do not the 20005 error will occur in which case the CDU will need to be reprogrammed to match the AP on the mainboard. Do RESET at Operator Function 2. http://domcached.com/error-code/hyosung-atm-errors.html

Initializ2. Recommended Action: See the recommended action for error code 144. Complete several test dispenses. Clean CS1B and CS13 4002ACS11B and CS13 Dark detection during initializing or dispense reserved operationThe same as #40022 and #40028 error handling 4002A00Detecting CS1B, CS13 Dark 4002BCS1A, CS1B or CS13 sensor

Nautilus Hyosung Error Codes

Exchange Cash Dispenser B/D1800CE, 2700CE, 5000CE, 5300CE40047001 cassette mis-feed error (Separated rejection)1. If the error does not show again put the cash dispenser into service. If all sensors are operation correctly, and the error persists, replace the replace the dispenser.

  • Recommended Action: See the recommended action for error code 144.
  • Test the dispensing mechanism by completing several test dispenses.
  • Verify that CS8 or encoder wheel sensor is in place and wire connection is good.
  • Remove any documents blocking the throat opening.
  • Clean CS2, CS4A and CS4B 4001DCS2, CS4A and CS4B Dark detection during initializing or dispense reserved operationThe same as #40011, #40014 and #40018 error handling 4001D00Detecting CS2, CS4A, CS4B Dark 4001ECS3,
  • C0057 Cassette information is not properly set CDU programming is not accurate or complete.
  • Recommended Action: See the recommended action for error code 128.

Verify that all access panels are closed and secured. Error Code: 364 Description: Dispenser device offline. Check the CDU information setting (4 Cassettes). 2. Epp Error Atm Reboot ATM 2.

If this error persists, the printer will require service.1700, 1700W, 2100T, C4000, G1900, G2500, GT3000, MB1000, MB1500, MB1800, MB2000, MB2100, T4000Axxx3Receipt Paper JamRemove jammed paper - Release receipt paper drawer by Hyosung Error Code 97999 Check if printer head lever is properly close1800CE, 2700CE, 5000CE, 5300CE2010900No sensing black mark (dark sensor)1. Change Cash Dispenser B/D 40034Error of two sheets detecting sensor(CS5_1)1. http://www.cordfinancial.com/support-center/atm-error-codes/nautilus-hyosung-atm-error-codes/ If error occurs when checking the CS31A (4 CST FM B/D CN3) disconnection operation, replace a sensor. 972210000Invalid Field1.

Reboot ATM 2. Hyosung 1800 Error Codes Reboot ATM 2. Call your attendant 9701070Create Mutex Fail for SIU(Sensor)1. Exchange sensor after abnormal operating CS13 Sensor 4004600Program error(Separated rejection)1.

Hyosung Error Code 97999

Check Cash Dispenser Firmware Version1800CE, 2700CE, 5000CE, 5300CE4005100Received a request for over 150 notes dispensing on the Cash Dispenser from the upper unit.1. Check wiring to mainboard.1700, 1700W, 2100T, C4000, G1900, G2500, GT3000, MB1000, MB1500, MB1800, MB2000, MB2100, T4000C00E1NS4 darkVerify connections to NS4 sensor. Nautilus Hyosung Error Codes The maximum number of notes that can be dispensed from the dispenser during a transaction is defaulted to fifty. Hyosung Error Code 97999(04) Check the wiring connections to the solenoid(s).

Otherwise service to cassette or dispenser may be required. this content If the sensor is not being pressed then the error will occur. Straighten and shuffle cash in the cassette.C0044More than 5 notes rejected consecutivelyVerify the quality of the cash. Check the clutch operation (Life test command)3. Hyosung Epp Error

Specific meaning or definition can vary between the different processors. Make sure that note qualifier and the note transport modules are mechanically aligned. Error Code: 103 (67h) Description: Thickness sensor unstable Recommended Action: Enter the diagnostic function and complete the “learn note thickness” command. weblink Check wiring connections to the CDU main board.

If the sensor is properly connected and operating correctly the CMC module may be defective. Hyosung 2700 Error Codes Recommended Action: Check data and power connections to the dispenser device. C00D1 Sensor blocked while dispensing MB2100T - A blockage was detected between the CS12 (upper cash tray sensor) and CS14 (lower cash tray sensor).

D0020 Surcharge screen should have been displayed Code reported by host processor.

Remove the remaining notes and foreign objects at the position of the CS41AB sensor 2. Make sure that the cassettes are installed and locked before performing a test dispense or live transaction. Note: If the modem is defective, this error will most likely occur frequently. Hyosung Tech Support Recommended Action: Check the dispenser data and power cable connections.

Error Code: 187 Description: Maximum withdrawal not configured. Recommended Action: See the recommended action for error code 144. Check if CS62 sensor poll is abnormal 3. check over here C00C9 CS12 & CS14 Sensors blocked MB2100T - Both the CS12 and CS14 sensors were blocked while the machine was either dispensing or initializing.

Initialize3. Excessive EMI emissions from outside source (neon sign, freezer)are likely causes. Check the status of Near End sensor and its connector 20808Receipt paper cuttimg error1. One or two instances of this error does not usually indicate a defective part.