Home > Error Code > Hp Numeric Error Codes

Hp Numeric Error Codes

Contents

Check the duplexer and the rear area of the printer for obstructions or damage. 2. If the error no longer exists, install each DIMM and EIO device one at a time, making sure to turn the printer off and back on as you install each device. Recommended action Verify that the output device is properly connected to the MFP. Replace the environmental thermistor. 4. Source

and may not be used without advance written permission of PrinterTechs.com, Inc. top Provide feedback Please rate the information on this page to help us improve our content. top 65.XX.YY OUTPUT DEVICE DISCONNECTED (LJ9040mfp/9050mfp) Explanation The output device is reporting that is disconnected from the MFP. Recommended action Turn the MFP off.

Hp Printer Error Code 49

Open and close the top cover to clear the message. 6. From the configuration page, determine the number of pages since the last maintenance. Replace the formatter. 79 & 80 errors - general info. HP DJ 500 System error 01:13 A problem with the Electronics module has occurred.

Turn the product off, and then turn the product back on. CALL TOLL FREE: 1-800-815-2737 All rights Reserved Laser Printer Services ©1991-2016 - Laser Printer Services Logo, this website and its contents, are property of Laser Printer Services. Recommended action Click here for assistance in troubleshooting and resolving 49 errors. (http://www.hp.com/cposupport/en/docs/bpl11422.html) 49.xxxxx errors can also be caused by software. 50.1 Fuser Error top 60.x PRINTER ERROR Explanation An obstruction prevents the tray specified by xx from lifting paper properly for feeding.

Open and close the front door to clear the message. Also check the external paper handling PCA 68 NVRAM ERROR CHECK SETTINGS An error occurred in the printer non-volatile memory (NVRAM) and one or more printer settings has been reset to top Paper jams Media jams occur either when media does not reach or does not clear a photo sensor along the printer paper path in a specific amount of time. try here If a stapler/stacker is attached, carefully pull out any paper that might be protruding from the accumulator area.

top 30.01.yy SCAN FAILURE Explanation The product fails to scan correctly. Hp Warranty Check Figure 30: Removing paper Reinstall the duplex printing accessory by sliding it back into the slot until it locks into place (Figure 31). Events usually conclude with a time-out or no response from the device (error 66.xy in the event log). Error Code 10.10 Supply Memory Error Error Code 41.3 Unexpected Paper Size Error Code 49, 494c02 firmware error Error Code 50, 50.1, 50.2, 50.3, ,50.4, 50.5, 50.6. 50.7 Error Code 51,

  • If a single setting is not present in the application, but is set in the driver, that will override the control panel settings.
  • Use the UP or DOWN ARROW keys to scroll to Diagnostics and press SELECT.
  • If printing still fails with all EIO devices removed, remove all memory DIMMs or third-party DIMMs from the printer. (Do not remove the firmware DIMM-- printer won't function without this installed.)
  • appears in an error message or a message alternates with FOR HELP PRESS ?, press the ?
  • Recommended action Touching Continue should clear the message.
  • Check the event log for specific error trends in the last 10,000 printed pages.

Hp Printer Error Codes List

X PRINTER ERROR a loss of beam detects occurred. http://www.printertechs.com/printer-troubleshooting/hp-error-codes/192-numeric-error-codes-20-49-hp-laserjet top top 69.x PRINTER ERROR Explanation A temporary printing error occurred. Hp Printer Error Code 49 Remove all EIO devices from the printer (JetDirect cards, hard drives, etc.). Hp Laptop Error Codes Home Contact Us Laser Printer Service Laser Printer Repair Laser Printer Parts HP LaserJet Service HP Error Codes HP Plotter Repair Discount/ Free Offer Company Info Los Angeles and Orange

Verify if the error occurs on specific or all print jobs. http://domcached.com/error-code/ibm-aix-error-codes.html Turn the printer off, and reseat or replace the specified DIMM. 2. The cable being used (by part number) and where it was purchased. Figure 14: Pulling down the green handle Carefully pull out any paper from the paper path module. Hp Printer Error Code List Pdf

If a message persists after performing all of the recommended actions, contact an authorized HP Service or Support Provider: Click here for information on contacting HP Customer Care. System error 56:13 An error in the drive roller encoder sensor quadrature has occurred. A message New Maintenance will appear in the control panel display and the printer will reset. http://domcached.com/error-code/hp-mfp-error-codes.html Check that all damaged or jammed paper is removed from product.

Figure 52: Sliding the stapler unit in Close the stapler-unit door (Figure 53). Hp Printer Support Remove the staple cartridge (Figure 47). Turn the printer off, and then turn the printer on.

Use the UP or DOWN ARROW keys to scroll to Set Paper Path Test, and then press SELECT.

To check the fuser, turn the printer off and remove the fuser. If the short cut method doesn't reset the maintenance count then you will need to go service mode to manually reset the maintenance count to zero. If error persists, replace the formatter. Hp Support System error 86:13 Carriage-Axis shutdown (firmware error).

Figure 36: Opening the stapler unit door On the staple cartridge, squeeze the tabs together and pull the cartridge out (see Figure 37). Check sensors and flags for proper operation Tech Support Support Home PageMaintenance Kit InstructionsOther instructionsTroubleshootingArticles, news, blog Featured Articles HP Error CodesEntering Service ModeService mode PIN codesCounterfeit parts challengeCold reset instructionsClearing If the problem is not related to the fuser, replace the engine controller board. 50.4 PRINTER ERROR A problem exists with the customer’s line voltage. 1. Check This Out See the HP LaserJet Printer Family - Print Media Guide (http://www.hp.com/support/ljpaperguide).

Plug the printer into a wall outlet and see if this resolves the problem. 3. Also verify the entire paper path is clear to prevent a recurring paper jam error message. Your cache administrator is webmaster. top 40 BAD SERIAL TRANSMISSION or 40 EIO x BAD TRANSMISSION Explanation A serial data error (parity, framing, or line overrun) occurred during the reception of data from the computer.

Press the checkmark button once. (Note: on LaserJet's 4200, 4300, 9000 you can hold down the checkmark button as you turn the power on and then wait for the three LEDs The 50 most recent events will be displayed, first to last. Figure 12: Lifting the green handle Carefully pull out any paper from the flipper area (Figure 13). HP Printer Error Codes HP Laser Printer Error Code 13 paper jam/Jamming Paper accordion 14 No EP Cartridge Paper Jam in the tray Squeeking Noise Grinding Noise Fuser paper jam error

See “Resolving Control Panel Messages" in the HP LaserJet 9000mpf Use Guide and follow the recommended action. Turn the printer off, and then turn the printer on. Figure 35: Moving the stapler/stacker Open the stapler unit door (see Figure 36). If a message persists after performing all of the recommended actions, contact an authorized HP Service or Support Provider: Click here for information on contacting HP Customer Care.

Figure 39: Pushing the cartridge lever down Insert the staple cartridge so that it snaps into place (see Figure 40). Click here for information on clearing jams from the right door area. Thanks to Mike Rose for erors 129 and 229!