REGISTRATION PAGE Printing... Clearing event log Clearing paper path CLOSE TOP COVER AND FRONT DOOR CODE CRC ERROR Creating...CLEANING PAGE DATA RECEIVED alternates with Ready Event Log Empty Genuine HP supplies installed GENUINE HP If the message persists, contact HP support. If that works go back to the first application and try printing a different file to determine if the problem is file related.
On rare occasions a defective paper control assembly or actuator can cause this problem. Action Open the front door and clear the jam. Caution needs to be used when installing the new assembly - be careful of the sensor flag spring! 5Si - Can be caused by field replaceable units (FRU's) not installed correctly. If the problem persists and is application specific, verify proper setup with application vendor. http://www.all-laser.com/aerror-code/
Hp Printer Error Codes List
There are LETHAL voltages inside of a laser printer and untrained personnel should refrain from doing anything other than determining that the error code in question is caused by a hardware Power printer off/on Excessive memory. This message appears until an HP supply is installed or (Checkmark) button is pressed. Explanation A printer error has occurred.
Check I/O Cable, it could be the wrong cable or damaged. For 68.0 errors, turn the printer Off and then On. top Event Log Empty Explanation SHOW EVENT LOG was selected from the control panel, and the event log is empty. Hp Printer Error Code List Pdf top 68.X STORAGE ERROR SETTINGS CHANGED Description One or more printer settings that were saved in the non-volatile storage device are invalid and have been reset to the factory default.
Replace high voltage power supply. 4V Bad toner cartridge microswitch SW501 on HV power supply Bad front door open sensor. Hp Error Code Oxc4eb827f If a 68.0 error persists, contact HP Support. Lower rear door completely, and then remove all media found. Print a configuration page and check the printer settings to determine which values have changed. 2.
top MANUALLY FEED alternates with To use another tray press MANUALLY FEED alternates with To use another tray press (Checkmark). LAN HW Test menu, remove the LAN cable, perform Communication troubleshooting 395 Embedded Jetdirect menu. Any help here would be appreciated too. Explanation The file system is protected and no new files can be written to it. Hp Inkjet Printer Error Codes
A switch on this assembly may not be activated properly. Make sure to try all solutions suggested, especially upgrading the Jetdirect firmware.7. Explanation The printer is restoring settings. Error 30 PS Error XX ALL PRINTERS PCL file was sent to the printer while in PostScript mode or the PostScript file contains bad data, or you have experienced and application
top RAM DISK FILE SYSTEM IS FULL alternates with Ready To clear press RAM DISK FILE SYSTEM IS FULL alternates with Ready To clear press (Checkmark). Hp Printer Error Symbols NOTE: If the product fails before you open the a product cold reset, and then perform a loopback test. top 13.XX.YY JAM IN TRAY 1 Description A page is jammed in the multipurpose tray.
In other cases, because the embedded LAN is part of the product firmware, the LAN error codes are within the 49.X series.
top MEM TEST FAILURE REPLACE DIMM 1 Explanation The memory DIMM has failed.
If the message persists, contact HP Support.
Configure is properly.
Check fuser bulb turn on. top Request accepted please wait Explanation The printer has accepted a request to print an internal page, but the current job must finish printing before the internal page will print. Paper sensor arm stuck or broken. 3. Hp Printer Error Code 79 NOTE: Any button pressed during the ten-second display of an auto-continuable error message will override the auto-continue feature and the function of the button pressed will take precedence.
top 41.3 UNEXPECTED SIZE IN TRAY X alternates with LOAD TRAY X 41.3 UNEXPECTED SIZE IN TRAY X alternates with LOAD TRAY X Explanation Media is loaded Recommended action No action necessary. Recommended action If an HP supply is been purchased, go to www.hp.com/go/anticounterfeit . If the problem persists, contact HP Support. 8X.YYYY EMBEDDED JETDIRECT ERROR Description The HP Jetdirect embedded print server has encountered a critical error.
To remove this message from the display, press (Checkmark). Explanation The printer encountered a request for a personality that did not exist in the printer. Press the spring contacts and listen for the micro switches. top Clearing paper path Explanation The printer jammed or detected misplaced media.
If the printer is unable to clear the jam automatically, see "Clearing paper jams" in the Use Guide, or press the HELP button (question mark) for help. To remove this message from the display, press (Checkmark). Recommended action Press (Down arrow) to see step-by-step information. Recommended action Attempt the upgrade again.
Replace appropriate fan as needed. Hold down CANCEL JOB while turning the printer on. PAPER PATH TEST PRINTING STOPPED To continue press Printing... top SB STORAGE X REMOVED Explanation The USB storage accessory was removed while the printer was turned On.
The printer will return to the Ready state when the page has printed. Action Press to continue printing. top top 41.3 UNEXPECTED SIZE IN TRAY X Description Media is loaded that is longer or shorter in the feed direction than the size configured for the tray. A buildup of toner on the edges of the tray which slides into the printer can sometimes cause problems.
top TRAY XX EMPTY alternates with Ready TRAY XX EMPTY alternates with Ready. DIAGNOSTICS PAGE Explanation The printer is generating the diagnostics page. See HP Web Jetadmin for more information.