Home > Error Code > Hp Error 13

Hp Error 13

Contents

Check sensors and flags for proper operation. 13.1 PAPER JAM OPEN INPUT TRAYS Paper-delay jam at paperfeed area. 1. Then disconnect the power cable from the wall outlet. Solution: Check the product for a jam. It might take a few seconds to change.

Paper jam- check all Trays. 2. Gemini02 I work on behalf of HPClick the Thumbs Up below to say “Thanks” for helping! If not, come back and we'll try something else. From the service manual: "Page 69: Transfer roller CAUTION: Do not touch the black rubber on the roller.

Hp Printer Error Codes List

Try removing and reseating the fuser. 5. HP LASER PRINTER 5000, 5100, 52001. A jam has occurred in the specified location.2. Transfer roller guide not seated. 5.

  1. Bad D.C.
  2. Is there anything else you can think of that would help in pin pointing the problem.Thanks,Joe by unknown on Jul 22, 2006 at 7:55am Add comment Please sign in to comment
  3. If they are not, replace the Fuser Drive Assembly. 1 Serrano OP Uncle Slayton Aug 1, 2016 at 7:49 UTC http://h30434.www3.hp.com/t5/LaserJet-Printing/Printer-Laserjet-600-M602-error-13-b9-ff-Jam-in-top-c...
  4. See the clear jams section in the service manual.
  5. The lower tabs that pivot the back cover should fit into grooves in the sheet metal on each side.
  6. Duplex paper path is obstructed or contains wornComponents. 5.
  7. Paper jam internally / under the toner cartridge.6.
  8. If the heartbeat LED is off, turn the product power off, make sure that the formatter is fully seated, and then turn the product on.
  9. It might be necessary to reduce the stack height of media in the tray. 2.

Showing results for  Search instead for  Do you mean  or Post new question Post new question Question Reply Topic Options Subscribe Mark Topic as New Mark Topic as Read Float this Verify the media meets the specifications. 5. If the message persists, check the top door switch for proper operation. 13.5 PAPER JAM CHECK REAR DOOR Paper-delay jam at fuser. 1. Hp Printer Error Code List Pdf Paper fragment under oblique rollers. 4.

Replace the roller if necessary. 5. Hp Laptop Error Codes If the media does not reach or pass these sensors within a specific amount of time, the microprocessor on the DC controller PCA halts the product functions, and a jam error Slide the transfer roller to the left to remove it. my site This confuses the electronics as to when the paper actually has left the fuser.

Check sensors and flags for proper operation Tech Support Support Home PageMaintenance Kit InstructionsOther instructionsTroubleshootingArticles, news, blog Featured Articles HP Error CodesEntering Service ModeService mode PIN codesCounterfeit parts challengeCold reset instructionsClearing Hp Error Code Oxc4eb827f Paper jam open paper trays make sure paper is loaded properly. 2. Make sure you have correctly set paper management: paper size, type, trays etc. Open the following menus: ● Administration ● Troubleshooting ● Diagnostic Tests 3.

Hp Laptop Error Codes

Plug the device directly into the wall socket. http://www.advancedlaser-hp-error-codes.com/error_13.htm For all jam messages, do the following: 1. Hp Printer Error Codes List The MEDIA PASSING TIME above is calculated also based on the media size." Page 286 and following: 41.03.YZ Unexpected size in .... Hp Computer Error Codes Run test with one device taken off one at a time. 14.

Rear door open. 2. Changed maintenance kit. Paper jam- internally. 4. Could someone let me know what I could try next to fix this issue?I purchased the exit roller assembly rebuild kit and installed it. Hp Inkjet Printer Error Codes

By using this site, you accept the Terms of Use and Rules of Participation Hp Error Code 13, Service Repair Errors 13 Problems Message Remove jammed media from the specified location.3. If it is not enabled/started, Make sure to enable/start the service. check fuser ass'y for paper stopping at the fuser.

I just wanted to make sure you knew what procedure I already performed.Based on your note above, what else could I test to find root cause?Thanks again,Joe by unknown on Jul Hp Printer Error Symbols I wanted to update you on how I was doing. Reconnect connector (J122) on the Tray 2 media size switch, and then reconnect connector (J72) on the DC controller. 3.

Run the Fuser motor DCM1 drive test to verify that the Fuser Drive and Gears are functioning correctly.

Inspect and/or replace the feed and separation rollers. 4. Paper jammed up in the exit ass'y on the left side of printer.8. by dmzcompute on Jul 18, 2006 at 6:39pm Add comment Please sign in to comment 0 The fuser exit sensor is actually not on the fuser but on top of the Hp Printer Error Code 79 I re-examined the exit sensor and could not find any crack or miss positioning of the flag(s).

Page 221: Component tests These tests activate the selected component. 1. Initially, it seemed to be free, when I had the fuser assembly out during the examination. HP LASER PRINTER 5L, 6L, 3100, 31501. Shutter door not opening all the way.5.

Remove jam and click OK.