Home > Checkpoint Code > Ibm Xseries 345 Over Spec Error Lights

Ibm Xseries 345 Over Spec Error Lights

Contents

When the LED flashes, an invalid power-supply configuration has occurred. MEM When only the MEM LED is lit, a memory error has occurred. Make sure that the room temperature is not too high. If the CNFG LED and the MEM LED are lit, complete the following step: Check the system-event log in the Setup utility or IMM error messages. check over here

If the CNFG LED and the PS LED are lit, the system issues an invalid power configuration error. Bamptini 2700014RWA 6 Posts Re: x345 Over spec error light ‏2010-01-12T10:34:37Z This is the accepted answer. Comment Flag More Print this page Share this page You can't post conmments that contain an email address. × Comment Anonymously Video Images Add Your Answer Tips for a great answer: Remove the PCI riser card in connector 1, all DIMMs, and the microprocessor in socket 2.

Ibm Light Path Diagnostics

Covered by US Patent. The system returned: (22) Invalid argument The remote host or network may be down. Table 1. MenuExperts Exchange Browse BackBrowse Topics Open Questions Open Projects Solutions Members Articles Videos Courses Contribute Products BackProducts Gigs Live Courses Vendor Services Groups Careers Store Headlines Website Testing Ask a Question

To print the manual completely, please, download it. Im not at my server today. Make sure that both power supplies installed in the server are of the same type. Ibm X3650 Dasd Error Light I would check the CPU fan(s), as they are usually smaller, and tend to go bad before the other larger ones.

I have a Gigabit card ethernet and this card, run ok and can switch on from wol in other server but in this Xserver 345 can't switch on computer from wake Im not at my server today. try againI not then remove this DIMM and put in another one. SP A service processor error has been detected.

I know that in certain HP systems you can disable the power button so that it doesnt do anything. Ibm X3650 M3 Checkpoint Code Display 9f If the error remains, replace the following components one at a time, in the order listed, restarting the server after each: Replace the hard disk drive. Has anyone seen or spent countless hours on a resolution? 0 Comment Question by:bmonroe44 Facebook Twitter LinkedIn Email https://www.experts-exchange.com/questions/23882426/IBM-xSeries-345-Type-8670-OverSpec-Light.htmlcopy LVL 4 Best Solution bybmonroe44 Replaced the power chasis and everything checks Note: The server will not power-on when the microprocessor in socket 1 or 2 is not installed in the server. (Trained service technician only) Toggle the switch block (SW4), bit 3

  1. Regards, Alexander Novikov Russia, Moscow More...
  2. Updated on 2010-01-14T13:08:43Z at 2010-01-14T13:08:43Z by Bamptini Novikov_Alexander 100000HTD5 6932 Posts Re: x345 Over spec error light ‏2010-01-12T08:58:46Z This is the accepted answer.
  3. Please try the request again.

Light Path Diagnostics Checkpoint Codes

Bamptini 2700014RWA 6 Posts Re: x345 Over spec error light ‏2010-01-14T13:08:43Z This is the accepted answer. check this link right here now RAID Reserved. Ibm Light Path Diagnostics If the 12 V channel A error LED is lit, complete the following steps: Turn off the server and disconnect the power from the server. Ibm Checkpoint Code 9f LED Problem None An error has occurred and cannot be diagnosed, or the ASM processor has failed.

Check the IMM system event log and the system-error log for information about the error. NMI A nonmaskable interrupt has occurred, or the NMI button was pressed. Share?Profiles ▼Communities ▼Apps ▼ Forums System x Server Log in to participate Expanded section▼Topic Tags ? PS 2 When the LED is lit, the power supply in bay 2 has failed. Ibm Light Path Diagnostics Checkpoint Codes

Dec 25, 2008 | IBM eServer xSeries 346 1 Answer Constant beeping I would first check that all the fans are turning when you first power it up. Light path diagnostics panel LEDsFollow the suggested actions in the order in which they are listed in the Action column until the problem is solved. If the CNFG LED is not lit, the system might detect a memory error. this content It's worth a thousand words.

If it has, replace it. Ibm Checkpoint Codes The TEMP LED might also be lit. prev next Related Questions: 1 Answer System doesn't get on after shut down Check the system BIOS.

What Our Users Say Press & Media Contacts Advertising DMCA Policy Brands × Login Login to ManualsLib Don't have an account?

Check the LEDs on the system board to identify the component that caused the error. An additional LED is lit next to a failing PCI slot. He is reachable via his email at info -at- infinitelogix.com.my HTML Developer Subscribe to Blog via Email Enter your email address to subscribe to this blog and receive notifications of new Ibm Light Path Diagnostics Dasd 9f This is the accepted answer.

See System-board switches and jumpers for the location of the SW4 switch block on the system board. All rights reserved. For more information, see the "Hard disk drive problems". have a peek at these guys Reseat the hard disk drive backplane.

Please try the request again. If the 12 V channel E error LED is lit, complete the following steps: Turn off the server and disconnect the power from the server. Replace any components that are identified in the error logs. If a voltage regulator has failed, (trained service technician only) replace the system board.

Edit Close Save changes Attachments: Added items Uploading: 0% my-video-file.mp4 Complete. Issken Sep 28, 2009 | Dell PowerEdge 2950 (becwfk1_6) Server 2 Answers Dell PowerEdge 2450 Server issues FIrstly reseat all removable components in the system and retrySecond remove all DIMMS except Tip: The max point reward for answering a question is 15.