Remove the SAS/SATA RAID riser card, DIMMs in connectors 1 through 9, and the microprocessor in socket 1. Comment by Sam -- February 13, 2014 @ 3:28 AM Reply You can live with orange light , no issue. Replace the hard disk drive backplane. See "Parts listing" to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). weblink
Remove the PCI riser card from PCI riser connector 2 and the microprocessor in socket 2. If the MEM LED and the CNFG LED are lit, complete the following steps: Check the system-event log in the Setup utility or IMM error messages. Print This PagePrint ShareShare Url of this page: HTML Link: Bookmark Manuals Brands IBM Manuals Desktop x3550 - System - 7978 Installation manual IBM x3550 - System - 7978 Installation Manual: If the problem remains or if you are using an ACPI-aware operating system, suspect the system board. http://publib.boulder.ibm.com/infocenter/systemx/documentation/topic/com.ibm.sysx.7944.doc/r_light_path_diagnostics_table.html
Ibm X3650 Dasd Error Light
If any of the power channel error LEDs (A, B, C, D, E, or AUX) on the system board are lit also, see the section about power-channel error LEDs in Power If the CNFG LED is lit, the system issues an invalid microprocessor configuration error. For more information, see the "Hard disk drive problems". Make sure that the air vents are not blocked.
Determine whether the CNFG LED is also lit.
Turn off the server and disconnect the power from the server.
Reseat the failing fan, which is indicated by a lit LED near the fan connector on the system board..
If the MEM LED and the CNFG LED are lit, complete the following step: Check the system-event log in the Setup utility or IMM error messages.
Restart the server to see whether the problem remains.
One PCI riser-card assembly must always be present in PCI connector 2.
If you just installed an optional device, remove it, and restart the server. If the error remains, replace the following components one at a time, in the order listed, restarting the server after each: Replace the hard disk drive. Check the system-event log in the Setup utility or IMM error messages. Ibm Light Path Diagnostics Checkpoint Codes They must match in speed and cache size.
Join our community for more solutions or to ask questions. Ibm Light Path Diagnostics The BRD LED can be lit for the following conditions: Battery Missing PCI riser-card assembly Failed voltage regulator Check the system-event log for information about the error. Replace any components that are identified in the error logs. (See Event logs for more information.) MEM When only the MEM LED is lit, a memory error has occurred. Check the LEDs on the hard disk drives for the drive with a lit status LED and reseat the hard disk drive.
Remove the optical drive, fans, hard disk drives, and hard disk drive backplane. Ibm Checkpoint Codes Replace the failing fan, which is indicated by a lit LED near the fan connector on the system board (see Removing a hot-swap fan for more information). Restart the server to see whether the problem remains. (Trained service technician only) Reinstall the microprocessor in socket 1 and restart the server. Turn off the server by pressing the power-control button and hold it down for 5 seconds.
Check the system-error logs for information about the error. have a peek at these guys Browse other questions tagged power-supply-unit ibm-xseries diagnostic or ask your own question. Parent topic: Troubleshooting tables The request cannot be fulfilled by the server Sign In Upload Page of 102 Go Download Table of ContentsContents TroubleshootingTroublesh.. Remove all PCI Express and PCI-X cards, all PCI riser cards, the operator information panel, and the Ethernet adapter (if installed). Ibm X3650 M3 Checkpoint Code Display 9f
Make sure that the failing microprocessor, which is indicated by a lit LED on the system board, is installed correctly. The server unexpectedly shuts down, and the LEDs on the operator information panel are not lit. Check the error log to identify where the over-temperature condition was measured. http://domcached.com/checkpoint-code/ibm-x3550-error-code-9f.html Can anyone advise?
Diagnosing problems using light path diagnostics LEDs in two locations on the server are available to help you diagnose problems that might occur during installation. Ibm Light Path Diagnostics Dasd 9f Remove power from the server; then, reconnect the server to power and restart the server. Remove one of the power supplies to isolate the failed power supply.
If the server now starts, you might have installed more devices than the power supply supports.
Reinstall each device that you removed in step 2 one at a time, starting the server each time, to isolate the failing device. Shut down the system and remove the power cords from the server; then, reconnect the server to power and restart the server. Press the reset button to reset the server and run the power-on self-test (POST). Brd Error On Ibm Server Note: The server will not power-on when the microprocessor in socket 1 or 2 is not installed in the server. (Trained service technician only) Toggle the switch block (SW4), bit 3
The OVER SPEC LED on the light path diagnostics panel is lit, and the 12v channel AUX LED on the system board is lit. Restart the server to see whether the problem remains. Light Path Diagnostics OVER SPEC CPU REMIND MEM SP FAN PCI occurred, the system-error LED on the front of the light path diagnostics drawer is lit. this content Complete the following steps to correct the problem: Update the server firmware to the latest level (see Updating the firmware).
FAN A fan has failed, is operating too slowly, or has been removed. Join Now For immediate help use Live now! Which Pokémon are exclusive to each version? All rights reserved.