Home > Checkpoint Code > Ibm Qpi Error

Ibm Qpi Error

Contents

Run the Setup utility (see Using the Setup utility).Make sure that both processors are displayed by the system. Footer links Contact Privacy Terms of use Accessibility UEFI/POST diagnostic codes UEFI/POST diagnostic error codes can be generated when the server starts or while the server is running. Check the system-event log to determine the reason for the lit LED (see Event logs). If a non-supported processor is identified, remove the Processor or replace with a supported Processor.

If no memory fault is recorded in the logs and no DIMM connector error LED is lit, re-enable the memory modules using the Setup utility or the Advanced Settings Utility (ASU). Make sure that the CPU heat sink is properly attached to the CPU (see Installing a microprocessor and heat sink). (Trained technician only) If the error still occurs, replace the microprocessor Replace the front bezel (see Removing the bezel assembly and Installing the bezel assembly). (Trained technician only) Replace the system-board assembly (see Removing the system-board assembly and Installing the system-board assembly). Clear CMOS memory to ensure that all DIMM connectors are enabled (see System-board switches and jumpers). https://www.ibm.com/support/entry/portal/docdisplay?lndocid=migr-5097828

Ibm Checkpoint Code 9f

TEMP A system temperature or component has exceeded thermal specifications. Run the Setup utility (see Using the Setup utility).Make sure that both processors are displayed by the system. DIMM Failed Memory Test S.68005 : An error has been detected by the the IIO core logic on Bus [arg1].

  1. Make sure that the DIMMs are installed in the correct sequence (see Installing a DIMM for more information). (Trained service technician only) Replace the microprocessor that controls the failing DIMMs. (Trained
  2. Make sure that the room temperature is within the operating specifications (see Features and specifications).
  3. After installing the Pass 5 QPI Wrap cards, the Operating mode may be safely restored to the default setting of 'Maximum Performance.' x3850 X5, Machine Types 7143 and 7191 servers, and
  4. OVERSPEC There is insufficient power to power the system.
  5. Find the failing, missing, or mismatched microprocessor by checking the LEDs on the microprocessor board.
  6. Swap the affected memory modules (as indicated by the error LEDs on the system board or the event logs) to a different memory channel or microprocessor (see Installing a memory module
  7. If the error is corrected, then microprocessor 1 is bad and must be replaced.
  8. Manually re-enable all affected DIMMs if the server firmware version is older than UEFI v1.10.

Make sure that the room temperature is within the operating specifications (see Features and specifications). Processor CATERR(IERR) has asserted S.1100C : An uncorrectable error has been detected on processor [arg1]. An uncorrectable memory error was detected on processor [arg3] channel [arg4]. System Halted No Memory Could Be Configured Reseat the blade server in the BladeCenter (see Removing the blade server from the BladeCenter unit and Installing the blade server in a BladeCenter unit).

PCI SERR Detected S.2018001 : An Uncorrected PCIe Error has Occurred at Bus [arg1] Device [arg2] Function [arg3]. Ibm X3650 M3 Checkpoint Code Display 9f See Removing a microprocessor and heat sink and Installing a microprocessor and heat sink. 0x806f0107 806f0107-2584ffff Error Group 4, processor X (All CPUs) thermal trip [Note: X=1,2] Make sure that the Make sure that none of the air vents on the BladeCenter unit and on the blade server are blocked. System booted with default settings.

Check IBM support website for a firmware update required for the Processor and install the update. (Trained technician only) If the problem continues, replace the processor (see Removing a microprocessor and Ibm Checkpoint Codes See the Details section for more information. The Vendor ID for the device is % and the Device ID is %. Additional information The Installation and Service Guide will provide the necessary actions to perform when this error occurs.

Ibm X3650 M3 Checkpoint Code Display 9f

I.1800D : [I.1800D] A cache associativity mismatch has been detected for one or more processor packages. [I.1800D] A cache associativity mismatch has been detected for one or more processor packages. Reseat the following components one at a time in the order shown, restarting the server each time: Battery Failing device (if the device is a FRU, then it must be reseated Ibm Checkpoint Code 9f External QPI Link Failure Detected W.11004 : A processor within the system has failed the BIST. Ibm Error Codes I.58015 : [I.58015] Memory spare copy initiated. [I.58015] Memory spare copy initiated.

Reseat the blade server in the BladeCenter (see Removing the blade server from the BladeCenter unit and Installing the blade server in a BladeCenter unit). A fix for the OS hang was provided in the Second Quarter 2012 firmware package, but while the fix resolved some instances, it was determined not to be effective for all Remove all storage drives from the blade server (see Removing a hot-swap storage drive). The LOG LED might also be lit. Ibm Light Path Diagnostics Checkpoint Codes

Note: The PCI or MEM LED might also be lit. with chassis Reading: X, Threshold: Y Remove all expansion cards from the blade server (see Removing an I/O expansion card). Processors of the same model have mismatched Stepping ID A processor stepping mismatch has been detected for one or more processor packages. Run the Setup utility and select System Information > System Summary > Processor Details to view the microprocessor information to compare the installed microprocessor specifications. (Trained service technician only) Remove and

A failed DIMM has been detected to activate the memory online-spare feature. Ibm X3550 M3 DRIVER HEALTH PROTOCOL: Reports Invalid Health Status Driver DRIVER HEALTH PROTOCOL: Reports Invalid Health Status Driver. The Global Non-Fatal Error Status register contains %.

Reading: X, Threshold: Y Remove all expansion cards from the blade server (see Removing an I/O expansion card).

Reading: X; Threshold: Y Make sure that the room temperature is within the operating specifications (see Features and specifications). The system has booted with default UEFI settings. I.580A5 [I.580A5] Mirror Fail-over complete. Ibm Warranty Lookup The severity is abbreviated in the event log to the first character.

If the server firmware version is UEFI v1.10 or newer, disconnect and reconnect the server to the power source and restart the server. Replace the following components one at a time, in the order shown, restarting the server each time: (Trained service technician only) Microprocessor (Trained service technician only) System board 001100A Microcode updated Make sure that the DIMMs match and are installed in the correct sequence (see Installing a DIMM). 0051009 No memory detected. Processors have mismatched Bus Speed I.1800C : A cache type mismatch has been detected for one or more processor packages.

Make sure that none of the air vents on the BladeCenter unit and on the blade server are blocked. Make sure that the heat sink is properly attached to the microprocessor (see Installing a microprocessor and heat sink). 0x80010b00 80010b01-2101ffff Error System mgmt software (PCH Temp) temperature over non-recoverable threshold. Disable on-board devices that you can do without and that request I/O. Solution This is a permanent limitation for the affected systems.

Check IBM support website for an applicable device driver, firmware update, PDSG revision or other information that applies to this error. Make sure that none of the air vents on the BladeCenter unit and on the blade server are blocked. Unqualified DIMM Serial Number Detected An unqualified DIMM serial number has been detected: serial number [arg1] found in slot [arg2] of memory card [arg3].