Home > Checkpoint Code > Ibm Lightpath Error Codes

Ibm Lightpath Error Codes

Contents

CNFG A hardware configuration error has occurred. (This LED is used with the MEM and CPU LEDs.) If the CNFG LED and the CPU LED are lit, complete the following steps: Your cache administrator is webmaster. The following illustration shows the LEDs and connectors on the system board. Then pull down on the panel, so that you can view the light path diagnostics panel information. weblink

This information and the information in Light path diagnostics LEDs can often provide enough information to diagnose the error. VRM Reserved.   Parent topic: Light path diagnostics The request cannot be fulfilled by the server The request cannot be fulfilled by the server Light path diagnostics Light path diagnostics is If the MEM LED and the CNFG LED are lit, complete the following steps: Check the system-event log in the Setup utility or IMM error messages. Microprocessor and memory expansion tray LEDsLEDs Description Light path power LED When this LED is lit, it indicates that the capacitor on the microprocessor and memory expansion tray has sufficient power

Ibm X3650 M3 Checkpoint Code Display 9f

Replace a failing power supply. Reset button: Press this button to reset the server and run the power-on self-test (POST). To compare the microprocessor information, run the Setup utility and select System Information, then select System Summary, and then select Processor Details. (Trained service technician only) Replace an incompatible microprocessor.

  • Before you work inside the server to view light path diagnostics LEDs, read the safety information that begins on Safety and Handling static-sensitive devices.
  • Follow steps indicated in POST error codes and Integrated management module error messages.
  • This reveals the light path diagnostics panel.
  • RAID Reserved   SP The service processor (the IMM) has failed.
  • This information and the information in Light path diagnostics LEDs can often provide enough information to diagnose the error.
  • This display will provide error codes in the event of a microprocessor error or a power fault.
  • The system returned: (22) Invalid argument The remote host or network may be down.
  • Check the system-event log in the Setup utility or IMM error messages.

You might have to use a pen or the end of a straightened paper clip to press the button. If the problem remains, go to the "Before you call IBM Service" website. The panel should only be outside of the server a short time. Ibm X3650 Checkpoint Code Display Please try the request again.

Light path diagnostics LEDs This information provides descriptions for the light path diagnostics LEDs. Ibm Checkpoint Code 9f Note any LEDs that are lit, and then slide the light path diagnostics panel back into the server. The display does not provide error codes or suggest components to be replaced. http://publib.boulder.ibm.com/infocenter/systemx/documentation/topic/com.ibm.sysx.7945.doc/r_light_path_diagnostics_leds.html PCIe riser card LEDs This information provides the location of the LEDs on the PCIe riser card.

If the CNFG LED is not lit, the system might detect a memory error. Ibm Checkpoint Code E7 Replace any components that are identified in the error logs. (See Event logs for more information.) MEM When only the MEM LED is lit, a memory error has occurred. Press this button to force a nonmaskable interrupt to the microprocessor. When LEDs are lit to indicate an error, they remain lit when the server is turned off, provided that the server is still connected to power and the power supply is

Ibm Checkpoint Code 9f

FAN A fan has failed, is operating too slowly, or has been removed. Are you sure you want to continue?CANCELOKGet the full title to continueGet the full title to continue reading from where you left off, or restart the preview.Restart preview

scribd ERROR The requested Ibm X3650 M3 Checkpoint Code Display 9f Note: The system service label on the underside of the cover also provides information about the location of the light path diagnostics LEDs. Ibm Checkpoint Codes If the failure remains, go to the "Before you call IBM Service" website for additional troubleshooting information.

The server is restarted. By placing the system-error LED indicator in Remind mode, you acknowledge that you are aware of the last failure but will not take immediate action to correct the problem. Remove one of the power supplies to isolate the failed power supply. NMI A nonmaskable interrupt has occurred, or the NMI button has been pressed. Ibm Light Path Diagnostics Dasd 9f

If the CNFG LED and the MEM LED are lit, complete the following steps: Check the system-event log in the Setup utility or IMM error messages. The Reset button is in the lower right-hand corner of the light path diagnostics panel. Remove the server cover and look inside the server for lit LEDs. http://domcached.com/checkpoint-code/ibm-server-error-codes.html Make sure that the failing microprocessor, which is indicated by a lit LED on the system board, is installed correctly.

When both the MEM and CNFG LEDs are lit, the memory configuration is invalid or the PCI Option ROM is out of resource. Ibm X3650 Dasd Error Light Make sure that the air vents are not blocked. The power supplies are using more power than their maximum rating.

Reseat the DIMM.

Lit LEDs on this panel indicate the type of error that has occurred. A hard disk drive has failed or is missing. Replace any components that are identified in the error log. Light Path Diagnostics X3650 M2 CPU When only the CPU LED is lit, a microprocessor has failed.

If the error remains, replace the following components in the order listed, restarting the server after each: Replace the hard disk drive (see Removing a hot-swap hard disk drive for more Complete the following steps to correct the problem: Update the server firmware to the latest level (see Updating the firmware). Replace the hard disk drive backplane (see Removing the SAS hard disk drive backplane for more information). The panel should only be outside of the server a short time.

If the system-error LED is lit, it indicates that an error has occurred; go to step 2. LED Problem Action None, but the system-error LED is lit. If the CNFG LED is lit, then an invalid microprocessor configuration has occurred.