Home > Beep Codes > Hp Post Error 57

Hp Post Error 57

Contents

May be feed problem. Replace the system board. 304-Keyboard or System Unit Error Keyboard failure. Reseat the card and if available, swap with a known working card. If possible, replace the IC 1 long, 1 short DMA controller 1 failure- The DMA controller IC for channel 1 has failed. Source

Check for correct setup or defective CMOS chip or defective battery Math Coprocessor Test NPU registers and interrupt request functions CPU Clock Test Test interface between CPU and system at different Defective Tray Size Sensing or Configuration - Most trays have tabs which depress a series of switches when installed. The codes appear at the bottom right corner of the system’s VGA screen, after the self-test has progressed far enough to initialize the video monitor. Try rebooting the system. http://h20565.www2.hpe.com/hpsc/doc/public/display?sp4ts.oid=254896&docLocale=en_US&docId=emr_na-c01702138

Hp Beep Codes

X = Description 4 Printer Fan 7 Duplex Fan 1. You may have a worn pickup roller. Please go to HP Support Center. This option is enabled by default.

  • Replace the keyboard.
  • Reset as needed.
  • Can also indicate a mis feed or paper not being picked up.
  • Enter Computer Setup and run the Drive Protection System test under Storage > DPS Self-test.

Four series of beeps indicate a fatal error; that is, a problem exists which prevents the computer from starting. Thank you and your firm again, you were terrific. Replace the CPU Low 1-1-2 System board select failure- The motherboard is having an undetermined fault. Hp 4 Beeps Red Light Pause 0195 Front side bus mismatch.

An error record is logged to the system event log (SEL). Reseat fan cable. Replace the motherboard 3-2-3 Reserved 3-2-4Keyboard controller failure- The keyboard controller has failed. http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-c00812876 Credit to John Palmer.

See the Hardware Reference Guide on the Documentation and Diagnostics CD for instructions on installing a new battery, or contact an authorized dealer or reseller for RTC battery replacement. 163-Time & Hp Led Codes On the Laserjet 4/4+ an error 12 can indicate the top cover open or a broken tab on the cover assembly. Verify the tab on the cover is not broken. The message BMC Responding appears at the end of POST.

Hp Beep Codes 5 Beeps

RTC (real-time clock) battery may need to be replaced. http://www.all-laser.com/aerror-code/ Laser printers are page printers and require the entire page to be processed before beginning to print. Hp Beep Codes Clear CMOS. 610-External Storage Device Failure External tape drive not connected. Hp Beep Codes 6 Beeps Back back to top How did we do?

Enabling Quick Boot causes the BIOS to skip the memory test. No, create an account now. The system pauses if an error is found during POST and only resumes when you press the F1 key. The user might want to replace the unit. Hp Beep Codes 3 Beeps

Reinstall tape drive or press F1 and allow system to reconfigure without the drive. 611-Primary Floppy Port Address Assignment Conflict Configuration error. Replace the video adapter first. Replace the IC if possible 4-2-4 Unexpected interrupt in protected mode- This is a CPU problem. Remove and reinstall the supply, replace the supply.

May also be due to excess heat. Hp Laptop Beep Codes Error 13 Paper Jam Error Message Forms: 13.XX.YZ - additonal location info on display or 13.XX.YY - a jam exists in the media path Paper jams can be in the pickup Replace chassis, rear chassis, or front chassis fan. 514-CPU or Chassis Fan not Detected CPU or chassis fan is not connected or may have malfunctioned.

Tractor feed paper with the edges ripped off doesn't seem to work very well.

The RAM IC is probably bad 4 short System timer failure- The system clock/timer IC has failed or there is a memory error in the first bank of memory 5 short Enter Computer Setup and reset the IRQ in Advanced > Onboard Devices. 411-Network Interface Card Interrupt Conflict IRQ address conflicts with another device. Beeps Post Code Description of failure One short beep 0 POST process completed successfully - normal startup 1-1-1-3 02h Verify real mode 1-1-2-1 04h Get CPU type 1-1-2-3 06h Initialize system Hp 3 Long Beeps 4 Short Beeps Check the CMOS extended CMOS RAM or battery respectively if a failure occurs Manufacturing Loop Search for diagnostic tool used in manufacturing and run predetermined tests if found.

Parity Check 2 Parity RAM failure. Pause 0197 Processor speeds mismatched. Replace the video adapter 1 long, 3 short Video memory test failure- The video adapter's memory has failed. Unplug the power cord, re-seat the memory modules, and reboot the computer.

I verified this with a SIIG (crap -- avoid like the plague) Ultra-66 card, and then confirmed the results with Dell. Feel free to shoot me a PM with updates or corrections. Beep codes for American Megatrends, Inc (AMI) BIOS The following AMI beep codes can occur when there is a problem during the attempt of a normal system startup. I am new to this and do not want to screw this up.

Pause 0103 ERROR! Reflash the system ROM with the latest BIOS image. 511-CPU, CPUA, or CPUB Fan not Detected CPU fan is not connected or may have malfunctioned. If possible, replace the MPU Dec 27, 2007 #9 Tedster Techspot old timer..... Verify proper memory module type.